24AA02E48-I/SN Microchip Technology, 24AA02E48-I/SN Datasheet - Page 7

• Manufacturer Part Number: 24AA02E48-I/SN
• Description: IC EEPROM 2KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24AA02E48-I/SN

• Memory Size: 2K (256 x 8)
• Package / Case: 8-SOIC (3.9mm Width)
• Format - Memory: EEPROMs - Serial (with MAC Address)
• Memory Type: EEPROM
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Organization: 256 K x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.1 MHz
• Access Time: 3500 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.7 V
• Maximum Operating Current: 3 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 1.8 V , 2.5 V , 3.3 V , 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

3.0
The 24AAXXXE48 supports a bidirectional, 2-wire bus
and data transmission protocol. A device that sends
data onto the bus is defined as transmitter, while a
device receiving data is defined as a receiver. The bus
has to be controlled by a master device which gener-
ates the Serial Clock (SCL), controls the bus access
and generates the Start and Stop conditions, while the
24AAXXXE48 works as slave. Both master and slave
can operate as transmitter or receiver, but the master
device determines which mode is activated.
4.0
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
• During data transfer, the data line must remain
Accordingly, the following bus conditions have been
defined (Figure 4-1).
4.1
Both data and clock lines remain high.
4.2
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
FIGURE 4-1:
 2010 Microchip Technology Inc.
SDA
SCL
is not busy.
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
(A)
FUNCTIONAL DESCRIPTION
BUS CHARACTERISTICS
Bus Not Busy (A)
Start Data Transfer (B)
Stop Data Transfer (C)
Condition
Start
(B)
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
Acknowledge
Address or
Valid
(D)
24AA02E48/24AA025E48
to Change
Allowed
Data
4.4
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The data on the line must be changed during the low
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of data
bytes transferred between Start and Stop conditions is
determined by the master device and is, theoretically,
unlimited (although only the last sixteen will be stored
when doing a write operation). When an overwrite does
occur, it will replace data in a first-in first-out (FIFO)
fashion.
4.5
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this Acknowledge bit.
The device that acknowledges has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable-low during the high
period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into
account. During reads, a master must signal an end of
data to the slave by not generating an Acknowledge bit
on the last byte that has been clocked out of the slave.
In this case, the slave (24AAXXXE48) will leave the
data line high to enable the master to generate the Stop
condition.
Note:
Data Valid (D)
Acknowledge
The 24AAXXXE48 does not generate any
Acknowledge
programming cycle is in progress.
(D)
bits
if
DS22124D-page 7
an
Condition
Stop
(C)
internal
(A)