MAX9263GCB/V+T Maxim Integrated, MAX9263GCB/V+T Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
MAX9263GCB/V+T
Manufacturer Part Number
MAX9263GCB/V+T
Description
Serializers & Deserializers - Serdes GMSL Serializer w/HDCP Interface
Manufacturer
Maxim Integrated
Datasheet
1.MAX9263GCBVT.pdf
(71 pages)
30
HDCP Gigabit Multimedia Serial
Link Serializer/Deserializer
Table 1. Power-Up Default Register Map (see Tables 22 and 24) (continued)
X = Indeterminate.
Table 2. Power-Up Default Register Map (see Tables 23 and 25)
0xA8 to 0xAB
0xAC to 0xAF
0x98 to 0x9C
0x9D to 0x9F
0xA0 to 0xA3
0xB0 to 0xB3
0xB7 to 0xB9
0xBA to 0xFF
0xA4 to 0xA7
REGISTER
REGISTER
ADDRESS
ADDRESS
(hex)
(hex)
0xB4
0xB5
0xB6
0x00
0x01
0x02
0x03
0x04
POWER-UP DEFAULT
POWER-UP DEFAULT
0x03, 0x13, 0x43, 0x53
0x0000000000
0x1F or 0x5F
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x000000
0x000000
All zero
(hex)
(hex)
0x00
0x00
0x00
0x80
0x90
0x00
ASEED = 0x0000000000, optional RNG seed value is 0x0000000000
DFORCE = 0x000000, video data forced to 0x000000 when FORCE_VIDEO = 1
H0 part of SHA-1 hash value is 0x00000000
H1 part of SHA-1 hash value is 0x00000000
H2 part of SHA-1 hash value is 0x00000000
H3 part of SHA-1 hash value is 0x00000000
H4 part of SHA-1 hash value is 0x00000000
Reserved = 0000
MAX_CASCADE_EXCEEDED = 0, 7 or fewer cascaded HDCP devices attached
DEPTH = 000, device cascade depth is zero
MAX_DEVS_EXCEEDED = 0, 14 or fewer HDCP devices attached
DEVICE_COUNT = 0000000, zero attached devices
GPMEM = 00000000, 0x00 stored in general-purpose memory
Reserved = 0x000000
KSV_LIST = all zero, no KSVs stored
SERID = 1000000, serializer device address is 1000 000
RESERVED = 0
DESID = 1001000, deserializer device address is 1001 000
CFGBLOCK = 0, registers 0x00 to 0x1F are read/write
SS = 00 (SSEN = low), SS = 01 (SSEN = high), spread-spectrum settings depend
on SSEN pin state at power-up
RESERVED = 0
AUDIOEN = 1, I
PRNG = 11, automatically detect the pixel clock range
SRNG = 11, automatically detect serial-data rate
AUTOFM = 00, calibrate spread-modulation rate only once after locking
RESERVED = 0
SDIV = 00000, autocalibrate sawtooth divider
LOCKED = 0, LOCK output is low (read only)
OUTENB = 0 (ENABLE = low), OUTENB = 1 (ENABLE = high), OUTENB default
depends on ENABLE pin state at power-up
PRBSEN = 0, PRBS test disabled
SLEEP = 0 or 1, SLEEP setting default depends on CDS and MS pin state at
power-up (see the Link Startup Procedure section)
INTTYPE = 00, base mode uses I
REVCCEN = 1, reverse control channel active (sending)
FWDCCEN = 1, forward control channel active (receiving)
2
S channel enabled
POWER-UP DEFAULT SETTINGS
POWER-UP DEFAULT SETTINGS
2
C
(MSB FIRST)
(MSB FIRST)