1337GDCGI IDT, 1337GDCGI Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
1337GDCGI
Manufacturer Part Number
1337GDCGI
Description
Real Time Clock Real Time Clock
Manufacturer
IDT
Datasheet
1.1337GDCGI.pdf
(27 pages)
Specifications of 1337GDCGI
Rohs
yes
Function
Clock, Calendar, Alarm
Rtc Bus Interface
I2C
Date Format
YY-MM-DD-dd
Time Format
HH
Supply Voltage - Max
5.5 V
Supply Voltage - Min
1.8 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
SOIC-8
Battery Backup Switching
No
Part # Aliases
IDT1337GDCGI
Status Register (0Fh)
IDT® REAL-TIME CLOCK WITH I
IDT1337G
REA LTIME CLOCK WITH SERIAL INTERFACE
Bit 7
OSF
Bit 2: Interrupt Control (INTCN). This bit controls the relationship between the two alarms and the interrupt output
pins. When the INTCN bit is set to logic 1, a match between the timekeeping registers and the alarm 1 registers
activate the INTA pin (provided that the alarm is enabled) and a match between the timekeeping registers and the
alarm 2 registers activates the SQW/INTB pin (provided that the alarm is enabled). When the INTCN bit is set to
logic 0, a square wave is output on the SQW/INTB pin. This bit is set to logic 0 when power is first applied.
Bit 1: Alarm 2 Interrupt Enable (A2IE). When set to a logic 1, this bit permits the Alarm 2 Flag (A2F) bit in the
status register to assert INTA (when INTCN = 0) or to assert SQW/INTB (when INTCN = 1). When the A2IE bit is
set to logic 0, the A2F bit does not initiate an interrupt signal. The A2IE bit is disabled (logic 0) when power is first
applied.
Bit 0: Alarm 1 Interrupt Enable (A1IE). When set to logic 1, this bit permits the Alarm 1 Flag (A1F) bit in the status
register to assert INTA. When the A1IE bit is set to logic 0, the A1F bit does not initiate the INTA signal. The A1IE
bit is disabled (logic 0) when power is first applied.
Bit 7: Oscillator Stop Flag (OSF). A logic 1 in this bit indicates that the oscillator either is stopped or was stopped
for some period of time and may be used to judge the validity of the clock and calendar data. This bit is set to logic
1 anytime the oscillator stops. The following are examples of conditions that can cause the OSF bit to be set:
1) The first time power is applied.
2) The voltage present on VCC is insufficient to support oscillation.
3) The EOSC bit is turned off.
4) External influences on the crystal (e.g., noise, leakage, etc.).
This bit remains at logic 1 until written to logic 0. This bit can only be written to a logic 0.
Bit 1: Alarm 2 Flag (A2F). A logic 1 in the alarm 2 flag bit indicates that the time matched the alarm 2 registers.
This flag can be used to generate an interrupt on either INTA or SQW/INTB depending on the status of the INTCN
bit in the control register. If the INTCN bit is set to logic 0 and A2F is at logic 1 (and A2IE bit is also logic 1), the INTA
pin goes low. If the INTCN bit is set to logic 1 and A2F is logic 1 (and A2IE bit is also logic 1), the SQW/INTB pin
goes low. A2F is cleared when written to logic 0. This bit can only be written to logic 0. Attempting to write to logic 1
leaves the value unchanged.
Bit 0: Alarm 1 Flag (A1F). A logic 1 in the Alarm 1 Flag bit indicates that the time matched the alarm 1 registers. If
the A1IE bit is also a logic 1, the INTA pin goes low. A1F is cleared when written to logic 0. This bit can only be
written to logic 0. Attempting to write to logic 1 leaves the value unchanged.
Bit 6
0
Bit 5
2
C SERIAL INTERFACE
0
Bit 4
0
Bit 3
0
Bit 2
0
9
Bit 1
A2F
Bit 0
A1F
IDT1337G
REV L 102412
RTC