AX88780_07 ASIX [ASIX Electronics Corporation], AX88780_07 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
AX88780_07
Manufacturer Part Number
AX88780_07
Description
High-Performance Non-PCI Single-Chip 32-bit 10/100M Fast Ethernet Controller
Manufacturer
ASIX [ASIX Electronics Corporation]
Datasheet
1.AX88780_07.pdf
(55 pages)
3.5 Flow Control
enables the stopping of remote node transmissions via a PAUSE frame information interaction. When space of the packet
buffer is less than the threshold values (RXBTHD0, RXBTHD1), AX88780 will send out a PAUSE-ON packet to stop the
remote node transmission. And then AX88780 will send out a PAUSE-OFF packet to inform the remote node to retransmit
packet if it has enough space to receive packets.
3.6 Checksum Offloads and Wake-up
will detect the packet whether it is IP, UDP or TCP packet. If it is an IP packet, AX88780 will calculate the checksum of
header and put the result in checksum filed of IP. Then it continuously checks the packet whether it is UDP or TCP. It will
perform the checksum operation whenever it is a UDP or TCP packet. AX88780 also automatically skip the VLAN tag
when checksum is executed. AX88780 also supports to detect magic packet or link-up to wake up system when system is in
sleep state or needs to cold start by magic packet.
3.7 Fast-Mode support
access AX88780 by driving CSN to low and toggle WEN (write) or OEN (read). AX88780 can support the burst until
whole packet access. The access timing can refer to section 6.2.4 and 6.2.6. This mechanism is only for TX/RX buffer
access. For configuration register access, it must use single access.
3.8 Big/Little-endian support
pin to high to swap the data format. Below table can depict the relation. This swap is only valid in 32-bit mode.
3.9 10/100BASE-TX PHY
IEEE 802.3, IEEE 802.3u and ANSI X3.263-1995. It’s main features can described below.
Adaptive equalizer
the mathematical coefficient to match the cable length.
Baseline wander correct
transformer that blocks the Dc signal. When the AC signal loses its DC component, the AC signal becomes distorted. The
Baseline-Wander correct ill restores the DC component to AC signal and delivers it as a complete signal to receiver.
Link monitor/signal detect
generate a Signal Detected (SD) to MAC. If the level is below 400mV, the SD signal will be de-asserted 1ms.
Carrier detect and 4B/5B coding
meet IEEE 802.3u defined preamble (J/K/packets in 100BASE-TX) standards. If the packets meet the standards, the PCS
sub-layer will start to process the data and send to MAC engine. The PCS converts received/transmitted data according
IEEE 802.3u defined coding standards, such as 4B/5B and scrambling/de-scrambling.
In full duplex mode, AX88780 supports the standard flow control mechanism defined in IEEE 802.3x standard. It
To reduce the computing loading of CPU, AX88780 is built checksum operator for IP, UDP or TCP packet. AX88780
To improve the throughput in embedded system, AX88780 supports fast-mode for TX/RX buffer access. Host can
AX88780 supports “Big” or “Little” endian data format. The default is Little-endian. Designer can pull-up SPDLED
AX88780 integrates high performance PHY that is fully compliant with 10/100BASE-TX Ethernet standards such as
This equalizer mainly eliminates the distortions caused by inter-symbol interference (ISI) by automatically adjusting
The transmitter sends DC and AC signals as a pair. The receiving device and transmitting device each have a
This feature is used to detect the signal’s level. If the detected signal is above 400mV in 100BASE-TX mode, it will
The Physical Coding Sub-layer (PCS) checks with Physical Medium Attachment (PMA) data to see if the packets
D [3 1 :2 4 ]
D [7 :0 ]
D [2 3 :1 6 ]
D [1 5 :0 ]
D [2 3 :1 6 ]
D [1 5 :8 ]
Figure 4: data swap block
D [7 :0 ]
D [3 1 :2 4 ]
14
L ittle -e n d ia n
B ig -e n d ia n
ASIX ELECTRONICS CORPORATION
AX88780