M38197 Mitsubishi, M38197 Datasheet - Page 27

• Manufacturer Part Number: M38197
• Description: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
• Manufacturer: Mitsubishi

Fig. GA-7 Serial I/O1 register transfer operation in full duplex mode
Setting of Serial I/O Automatic Transfer
Timing
The timing of serial I/O automatic transfer is set with the serial
I/O1 control register (address 0019
matic transfer interval register (address 001C
The serial I/O1 control register sets the transfer clock speed,
and the serial I/O automatic transfer interval register sets the
serial I/O automatic transfer interval. This setting of transfer in-
terval is valid only when selecting the internal clock as the
clock source.
Start of Serial I/O Automatic Transfer
Automatic transfer mode is set by writing “1” to the bit 0 of the
serial I/O automatic transfer control register (address 001A
then automatic transfer starts by writing “1” to the bit 1.
The bit 1 of the serial I/O automatic transfer control register is
always “1” during automatic transfer; writing “0” can complete
the serial I/O automatic transfer.
Operation in Serial I/O Automatic Transfer
Modes
There are two modes for serial I/O automatic transfer: full du-
plex mode and transmit-only mode. Either internal or external
clock can be selected for each of these modes.
Transfer direction selection bit
Transfer clock
16
) and the serial I/O auto-
16
).
LSB first (SC1
MSB first (SC1
S
16
IN
),
5
5
= “0” ) : MSB
= “1” ) : LSB
(2.1) Operation in Full Duplex Mode
In full duplex mode, data can be transmitted and received at the
same time. Data in the automatic transfer RAM is transmitted in
sequence in accordance with the serial I/O automatic transfer data
pointer and simultaneously reception data is written to the auto-
matic transfer RAM.
The transfer timing of each bit is the same as that in ordinary op-
eration mode, and the transfer clock stops at “H” after eight
transfer clocks are counted.
When selecting the internal clock, the transfer clock remains at “H”
for the time set with the serial I/O automatic transfer interval regis-
ter, then the data at the next address (the address is indicated with
the serial I/O automatic transfer data pointer) are transferred.
If when selecting the external clock, the setting of the automatic
transfer interval register is invalid, so control the transfer clock ex-
ternally.
The last data transfer completes when the contents of the serial
I/O automatic transfer pointer reach “00
I/O automatic transfer interrupt request bit is set to “1” and the bit
1 of the serial I/O automatic transfer control register is cleared to
“0” to complete the serial I/O automatic transfer.
(2.2) Operation in Transmit-Only Mode
The operation in transmit-only mode is the same as that in full du-
plex mode, except for that data is not transferred from the serial
I/O1 register to the serial I/O automatic transfer RAM.
DO
DI
DI
DI
DI
0
1
2
7
7
DO
DO
DI
DI
DI
0
1
6
7
6
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DO
DO
DO
DI
DI
Serial I/O1 register
0
5
6
7
5
DO
DO
DO
DO
DI
•
•
•
4
5
6
7
4
MITSUBISHI MICROCOMPUTERS
DO
DO
DO
DO
DI
3
4
5
6
3
DO
DO
DO
DO
DI
2
3
4
5
2
DO
DO
DO
DO
DI
1
3
1
2
4
LSB
MSB
16
DO
DO
DO
DO
DI
”. At that point, the serial
3819 Group
0
0
1
3
2
S
OUT
27