ADC-8032A ETC [List of Unclassifed Manufacturers], ADC-8032A Datasheet - Page 42
ADC-8032A
Manufacturer Part Number
ADC-8032A
Description
Analog Composite to SDI Decoder
Manufacturer
ETC [List of Unclassifed Manufacturers]
Datasheet
1.ADC-8032A.pdf
(52 pages)
- Current page: 42 of 52
- Download datasheet (4Mb)
5-2 • SMPTE 269M Fault Reporting
Jumper Setup
If fault reporting for the ADC-8032A is desired, use jumper JP4 - 269M Fault Report to set up the
card.
Frame Connections
The SMPTE 269M Fault Reporting connection on RossGear 8000 series frames is provided by the
auxiliary telco connector, AUX A, for interfacing with a customer-designed alarm system.
Connect the frame’s AUX A connector to your facility’s SMPTE alarm circuit.
Details
The fault report contacts are closed when the card detects an internal failure or a power loss condition.
Some internal failures are:
For additional information on alarm system design, refer to the SMPTE document ANSI/SMPTE
269M - 1994.
1. To access the jumper, remove the card from the frame by pressing down the white
2. Observing all static discharge and handling precautions, place the card with the
3. To enable SMPTE fault reporting, set jumper JP4 to EN position. See the Jumper
4. To disable SMPTE fault reporting, set jumper JP4 to DIS position. See the Jumper
5. To return the card to the designated frame installation slot, hold the ADC-8032A
•
•
•
SMPTE 269M Fault Reporting
card ejector tab and pulling the card from the frame slot.
component side facing up on a clean flat surface.
Setup section in Chapter 2 “Installation and Setup”.
Setup section in Chapter 2 “Installation and Setup”.
card by the edges and carefully align the card edges with the slots in the frame. Then
fully insert the card into the frame until the rear connection plug is properly seated.
Failure of the card to initialize
Failure in the fault reporting circuitry
Failure to detect a valid analog input signal to the card
Aux A Connectors for
Figure 6. SMPTE 269M Alarm Reporting Frame Connections
ADC-8032A User Manual (Iss. 04)
Related parts for ADC-8032A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-Bit, 20MHz, Complete 8-Bit, 20MHz, Complete Flash A/D Converter
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
8-bit High-speed Flash A/d Converter
Manufacturer:
Murata Manufacturing Co., Ltd
Datasheet:
Part Number:
Description:
8-bit Ultrahigh- Speed Bipolar Silicon Flash A/d Converter
Manufacturer:
Murata Manufacturing Co., Ltd
Datasheet:
Part Number:
Description:
Dc Power Jacks Pc Board And Panel Mount Adc Series
Manufacturer:
Adam Technologies, Inc.
Datasheet:
Part Number:
Description:
Adc-hs-12b A/D converter
Manufacturer:
C&D Technologies.
Datasheet:
Part Number:
Description:
Directional Coupler Surface Mount
Manufacturer:
Mini-Circuits
Datasheet:
Part Number:
Description:
Directional Coupler Surface Mount
Manufacturer:
Mini-Circuits
Datasheet:
Part Number:
Description:
Directional Coupler Surface Mount
Manufacturer:
Mini-Circuits
Datasheet:
Part Number:
Description:
Directional Coupler 1000
Manufacturer:
Mini-Circuits
Datasheet:
Part Number:
Description:
8-bit, 20mhz, Complete Flash A/d Converter
Manufacturer:
C&D Technologies.
Datasheet:
Part Number:
Description:
256Kb FRAM Serial 3V Memory
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
INFRARED REMOTE CONTROL TRANSMITTER
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Adjustable Shunt Regulator
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
STEERING DIODE (RAIL CLAMP) ARRAY
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
MICROCONTROLLER BLOCK DIAGRAM
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet: