FTRJ-1319-XD ETC2 [List of Unclassifed Manufacturers], FTRJ-1319-XD Datasheet
FTRJ-1319-XD
Related parts for FTRJ-1319-XD
FTRJ-1319-XD Summary of contents
Page 1
... PH3 and FC-PI 10.0 . Digital diagnostics functions are available via an SPI serial bus. PRODUCT SELECTION Finisar Corporation 7-Jan-2002 Rev.G Product Specification FTRJ-1319-7D APPLICATIONS § 1.25Gb/s 1000Base-LX Ethernet § 1.0625Gb/s Fibre Channel 2 and Fibre Channel FC-PH, PH2, FTRJ-1319-xD x=7: LC connector; bail extraction 1 . They comply Page 1 ...
Page 2
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. ...
Page 3
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage ...
Page 4
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width Optical Extinction Ratio Optical Rise/Fall Time Relative Intensity Noise Transmitter Jitter (peak to peak) Receiver Average sensitivity Maximum input power Optical Center Wavelength ...
Page 5
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125 m SMF Notes: 1. Fibre Channel and IEEE 802.3 (Gigabit Ethernet) compatible. Typical maximum data rate extends to 1.5Gb/ 1.25Gb/s with PRBS 2 -1 ...
Page 6
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 VIII. Digital Diagnostic Functions Finisar FTRJ-1319-7D SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’ ...
Page 7
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the the SFP Multi-Sourcing Agreement (MSA) FTRJ-1319-7D (dimensions are in inches) Finisar Corporation 7-Jan-2002 Rev ...
Page 8
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 X. PCB Layout and Bezel Recommendations Finisar Corporation 7-Jan-2002 Rev Page 8 ...
Page 9
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 Finisar Corporation 7-Jan-2002 Rev Page 9 ...
Page 10
... FTRJ-1319-7D Pluggable SFP Product Specification – January 2002 XI. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. IEEE Std 802.3, 2000 Edition, Clause 38, PMD Type 1000BASE-LX. IEEE Standards Department, 2000. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. ...