ftrj-8519-7d ETC-unknow, ftrj-8519-7d Datasheet
ftrj-8519-7d
Related parts for ftrj-8519-7d
ftrj-8519-7d Summary of contents
Page 1
... Single 3.3V power supply § Low power dissipation <750mW § Extended operating temperature range: -10°C to 85°C Finisar’s FTRJ-8519-7D Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) with Gigabit Ethernet as specified in IEEE Std 802.3 3 PH3 and FC-PI 10 ...
Page 2
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported, pin grounded within module. FAULT 3 T Transmitter Disable. Laser output disables on high or open. DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. ...
Page 3
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage ...
Page 4
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr 62.5 MMF Optical Wavelength Spectral Width Optical Extinction Ratio Optical Rise/Fall Time Relative Intensity Noise Total Transmitter Jitter at TP2 Peak-to-Peak Jitter Contribution Receiver Receiver Sensitivity ...
Page 5
... UL/CSA Copies of the referenced certificates are available at Finisar Corporation upon request. VIII. Digital Diagnostic Functions Finisar FTRJ-8519-7D SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA the GBIC standard, with the same electrical specifications. Finisar Corporation 14-Jan-2002 Rev.D ...
Page 6
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage ...
Page 7
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) FTRJ-8519-7D (dimensions are in inches) Finisar Corporation 14-Jan-2002 Rev ...
Page 8
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 X. PCB Layout and Bezel Recommendations Finisar Corporation 14-Jan-2002 Rev Page 8 ...
Page 9
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 Finisar Corporation 14-Jan-2002 Rev Page 9 ...
Page 10
... FTRJ-8519-7D Pluggable SFP Product Specification – January 2002 XI. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. IEEE Std 802.3, 2000 Edition, Clause 38, PMD Type 1000BASE-SX. IEEE Standards Department, 2000. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. ...