SLIN-20E1A0 BEL [Bel Fuse Inc.], SLIN-20E1A0 Datasheet - Page 3

• Manufacturer Part Number: SLIN-20E1A0
• Description: NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /20 A Outputs
• Manufacturer: BEL [Bel Fuse Inc.]

Output Specifications
Notes: 1. Some output voltages may not be possible depending on the input voltage.
October 8, 2009
Output Voltage Set Point
Output Voltage
Adjustment Range
Remote Sense Range
Load Regulation
Line Regulation
Temperature Regulation
(-40°C to +85°C)
Ripple and Noise (pk-pk)
Ripple and Noise (rms)
Output Current Range
Output DC Current Limit
Output Short-Circuit Current
Output Capacitance
Turn-On Delay Time
Output voltage Rise time
Output voltage overshoot
Dynamic Load Response
△
△
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /20 A Outputs
of Max Load
of Max Load
V50%~100%
V100%~50%
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel [phone] • Fax [phone] •
3. Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and
2. External capacitors may require using the new Tunable Loop
stable as well as getting the best transient response (See the Tunable Loop
temperature conditions.
Parameter
ESR≥0.15 mΩ
ESR≥ 10 mΩ
ESR≥ 1 mΩ
1
V
V
Peak Deviation
Peak Deviation
V
V
2
Settling Time
Settling Time
O
O
O
O
≥ 2.5V
≥ 2.5V
< 2.5V
< 2.5V
0.69
Min
-1.5
-2.5
0
0
0
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Typ
120
2.6
30
14
2
2
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
380
300
30
30
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
10000
1000
Max
+1.5
+2.5
200
5.5
0.5
0.4
0.5
28
10
10
80
20
5
3
-
-
-
-
-
%Io,max
%Vo,set
%Vo,set
%Vo,set
%Vo,set
%Vo,set
-
-
-
-
Unit
mV
mV
mV
mV
mV
mS
mS
mS
uF
uF
uF
V
V
A
A
mV
mV
uS
uS
Over all operating input voltage, resistive load,
and temperature conditions until end of life
selected by an external resistor
I
V
V
5Hz to 20MHz BW, V
I
Hiccup Mode
Vo≤250mV, Hiccup Mode
Without the Tunable Loop
With the Tunable Loop
With the Tunable Loop
Case 1: On/Off input is enabled and then input
power is applied (delay from instant at which
V
Case 2: Input power is applied for at least one
second and then the On/Off input is enabled
(delay from instant at which Von/Off is enabled
until Vo =10% of Vo, set)
time for Vo to rise from 10% of Vo, set to 90%
of Vo, set
Vin=Vin, min to Vin, max, Io=Io, min to Io, max,
With or without maximum external capacitance
O
O, max
IN
O
IN
=I
TM
=V
< 2.5V, T
= V
O, min
di/dt=10A/us, Vin=Vin,nom, Vo=1.5V,
Ta=25°C, Co=0
feature to ensure that the module is
IN, min
Co = 0.1μF // 10 μF ceramic capacitors)
IN, min
to I
to V
O, max
ref
until Vo =10% of Vo, set)
=T
IN, max
A, min
TM
Notes
IN
section for details).
to T
TM
TM
=V
www.belfuse.com
A, max
IN, nom
TM
and I
O
=I
O, min
to
3