AM49DL640BG25IS SPANSION [SPANSION], AM49DL640BG25IS Datasheet - Page 58
AM49DL640BG25IS
Manufacturer Part Number
AM49DL640BG25IS
Description
Stacked Multi-Chip Package (MCP) Flash Memory and SRAM
Manufacturer
SPANSION [SPANSION]
Datasheet
1.AM49DL640BG25IS.pdf
(62 pages)
- Current page: 58 of 62
- Download datasheet (2Mb)
FLASH ERASE AND PROGRAMMING PERFORMANCE
Notes:
1. Typical program and erase times assume the following conditions: 25 C, 3.0 V V
2. Under worst case conditions of 90 C, V
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table
6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
LATCHUP CHARACTERISTICS
Note: Includes all pins except V
PACKAGE PIN CAPACITANCE
Notes:
1. Sampled, not 100% tested.
2. Test conditions T
FLASH DATA RETENTION
March 8, 2002
Parameter
Sector Erase Time
Chip Erase Time
Byte Program Time
Accelerated Byte/Word Program Time
Word Program Time
Chip Program Time
(Note 3)
Input voltage with respect to V
(including A9, OE#, and RESET#)
Input voltage with respect to V
V
Parameter Description
Minimum Pattern Data Retention Time
CC
programming typicals assume checkerboard pattern.
program faster than the maximum program times listed.
12 for further information on command definitions.
Parameter
Current
Symbol
C
C
C
C
OUT
IN2
IN3
IN
A
Parameter Description
Input Capacitance
Output Capacitance
Control Pin Capacitance
WP#/ACC Pin Capacitance
= 25°C, f = 1.0 MHz.
Description
SS
SS
CC
Word Mode
Byte Mode
on all pins except I/O pins
on all I/O pins
. Test conditions: V
CC
= 2.7 V, 1,000,000 cycles.
P R E L I M I N A R Y
Typ (Note 1)
CC
Am49DL640BG
= 3.0 V, one pin at a time.
0.4
56
42
28
5
4
7
Max (Note 2)
150
120
210
126
84
5
Test Setup
V
V
V
V
Test Conditions
OUT
IN
IN
IN
–100 mA
–1.0 V
–1.0 V
= 0
= 0
= 0
Min
= 0
CC
150 C
125 C
, 1,000,000 cycles. Additionally,
Unit
sec
sec
sec
µs
µs
µs
Excludes 00h programming
prior to erasure (Note 4)
Excludes system level
overhead (Note 5)
Typ
12
14
17
11
Comments
V
+100 mA
CC
12.5 V
Min
Max
10
20
Max
+ 1.0 V
14
16
16
20
Years
Years
Unit
Unit
pF
pF
pF
pF
57
Related parts for AM49DL640BG25IS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: