CBTD3384PW,112 NXP Semiconductors, CBTD3384PW,112 Datasheet
CBTD3384PW,112
Specifications of CBTD3384PW,112
CBTD3384PW
CBTD3384PW
Related parts for CBTD3384PW,112
CBTD3384PW,112 Summary of contents
Page 1
CBTD3384 10-bit level shifting bus switch with 5-bit output enables Rev. 5 — 19 November 2010 1. General description The CBTD3384 provides ten bits of high-speed TTL-compatible bus switching. The low ON resistance of the switch allows connections to be ...
Page 2
... NXP Semiconductors 4. Functional diagram Fig 1. Logic diagram 5. Pinning information 5.1 Pinning CBTD3384 1OE 1 2 1B1 3 1A1 1A2 4 1B2 5 1B3 6 7 1A3 8 1A4 1B4 9 1B5 10 1A5 11 12 GND 001aan060 Fig 2. Pin configuration for SO24 (SOT137-1) CBTD3384 Product data sheet 10-bit level shifting bus switch with 5-bit output enables ...
Page 3
... NXP Semiconductors Fig 4. Pin configuration for SSOP24 (SOT556-1) 5.2 Pin description Table 2. Pin description Symbol Pin 1OE, 2OE 1, 13 1A1 to 1A5 2A1 to 2A5 14, 17, 18, 21, 22 1B1 to 1B5 2B1 to 2B5 15, 16, 19, 20, 23 GND Functional description [1] Table 3. Function selection Input 1OE 2OE [ HIGH voltage level LOW voltage level high-impedance OFF-state. ...
Page 4
... NXP Semiconductors 7. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). − ° ° +85 C, unless otherwise specified. amb Symbol Parameter V supply voltage CC V input voltage I I output current O I input clamping current IK T storage temperature ...
Page 5
... NXP Semiconductors Table 6. Static characteristics Voltages are referenced to GND (ground = 0 V). Symbol Parameter R ON resistance ON [1] All typical values are [2] This is the increase in supply current for each input that is at the specified TTL voltage level rather than V [3] Measured by the voltage drop between the nAn and the nBn terminals at the indicated current through the switch. ON resistance is determined by the lowest voltage of the two (nAn or nBn) terminals ...
Page 6
... NXP Semiconductors 3.6 V pass (V) 3.2 2.8 2.4 2.0 4.4 4.8 = 100 μ ( Fig 7. Pass voltage versus supply voltage °C (typical) T amb = 100 μ ( Fig 9. Pass voltage versus supply voltage; T CBTD3384 Product data sheet 10-bit level shifting bus switch with 5-bit output enables ...
Page 7
... NXP Semiconductors 10. Dynamic characteristics Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V). For test circuit see Symbol Parameter t propagation delay pd t enable time en t disable time dis [1] The propagation delay is the calculated RC time constant of the typical ON resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance) ...
Page 8
... NXP Semiconductors nOE input output LOW to OFF OFF to LOW output HIGH to OFF OFF to HIGH Measurement points are given in Logic levels: V and Fig 11. Enable and disable times Table 8. Measurement points Supply voltage Input 5.0 V ± 0 GND to 3 CBTD3384 Product data sheet 10-bit level shifting bus switch with 5-bit output enables ...
Page 9
... NXP Semiconductors 12. Test information Test data is given in Table All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz; Z The outputs are measured one at a time with one transition per measurement. Definitions for test circuit Load resistance Load capacitance including jig and probe capacitance. ...
Page 10
... NXP Semiconductors 13. Package outline SO24: plastic small outline package; 24 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT max. 0.3 2.45 mm 2.65 0.25 0.1 2.25 0.012 0.096 inches 0.1 0.01 0.004 0.089 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. ...
Page 11
... NXP Semiconductors SSOP24: plastic shrink small outline package; 24 leads; body width 5 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.21 1. 0.25 0.05 1.65 Note 1. Plastic or metal protrusions of 0.2 mm maximum per side are not included. OUTLINE VERSION IEC SOT340-1 Fig 14. Package outline SOT340-1 (SSOP24) ...
Page 12
... NXP Semiconductors SSOP24: plastic shrink small outline package; 24 leads; body width 3.9 mm; lead pitch 0.635 DIMENSIONS (millimetre dimensions are derived from the original inch dimensions) A UNIT max. 0.25 1.55 mm 1.73 0.25 0.10 1.40 0.0098 0.061 inches 0.068 0.01 0.0040 0.055 Note 1 ...
Page 13
... NXP Semiconductors TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.15 0.95 mm 1.1 0.25 0.05 0.80 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. ...
Page 14
... Document ID Release date CBTD3384 v.5 20101119 • Modifications: The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • Legal texts have been adapted to the new company name where appropriate. • Table CBT3384 v.4 20011220 CBT3384 v ...
Page 15
... In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or ...
Page 16
... NXP Semiconductors Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 17. Contact information For more information, please visit: For sales office addresses, please send an email to: CBTD3384 Product data sheet 10-bit level shifting bus switch with 5-bit output enables 16 ...
Page 17
... NXP Semiconductors 18. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 1 4 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 5 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 5.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 6 Functional description . . . . . . . . . . . . . . . . . . . 3 7 Limiting values Recommended operating conditions Static characteristics 9.1 Typical pass voltage graphs . . . . . . . . . . . . . . . 5 10 Dynamic characteristics . . . . . . . . . . . . . . . . . . 7 11 Waveforms ...