HEDS-6500 HP [Agilent(Hewlett-Packard)], HEDS-6500 Datasheet
HEDS-6500
Related parts for HEDS-6500
HEDS-6500 Summary of contents
Page 1
... The outputs of the HEDS- 6500 are two single ended square waves in quadrature. The HEDL- 65xx outputs are differential. The HEDS-6540 / HEDL-6540 also ...
Page 2
... SLOTTED (0.010) 13.2 (0.52) 65.9 (2.59) HEDS-65XX #xxx YYMM COUNTRY OF ORIGIN 24.9 (0.98) 30.2 (1.19) 2 Eg. ABS braking systems, power steering, life support systems and critical care medical equipment. Please contact sales representative if more clarification is needed. 609.6 (24.0 ± ...
Page 3
... LENS LED SIGNAL PROCESSING CIRCUITRY EMITTER CODE SECTION WHEEL There are two different connector pin-out configurations used with the HEDS-65xx / HEDL-65xx series of encoders. The table below relates the part to its connector pin-out. Connector Pin-out COMPARATORS INDEX-PROCESSING CIRCUITRY DETECTOR SECTION COMPARATORS INDEX-PROCESSING ...
Page 4
... Theory of Operation The HEDS-65xx / HEDL-65xx translate the rotary motion of a shaft into either a two or three channel digital output. The HEDS-65xx uses one of the standard HEDS-9000 or HEDS-9040 modules for encoding purposes. The HEDL-654x uses the standard HEDL-9040 for encoding purposes. As seen in the block diagram, ...
Page 5
Output Waveforms OUTPUT PHASE OUTPUT CH I OUTPUT Waveforms for Encoders without Line Drivers Waveforms for Encoders with Line Drivers. (Meets all requirements of EIA-422.) S3 ...
Page 6
... 30,000 30,000 30,000 HEDS-6500 HEDS-6540 HEDL-6540 HEDL-6545 -40 to +100 -40 to +100 -40 to +100 4.5 to 5.5 4.5 to 5.5 4.5 to 5.5 100 100 100 100 .05 .05 ( .002) ( .002) ( .002) 6 -40 to +100 ...
Page 7
... Position Error Cycle Error Index Pulse Width *Typical values specified 5.0 V and 25 C. **HEDS-6540 – Active high Index part. Pull-up of 2.7 k used on all outputs of modules that do not have a line driver. ***HEDS-6500 – 3.3 k pull-up resistors used on all encoder module outputs. 7 Symbol Min. ...
Page 8
... Electrical Characteristics Electrical Characteristics over Recommended Operating Range, typical Part Number Symbol* Min. HEDS-6500 2 HEDS-6540 2 *Explanation for symbols – Supply current, V – High Level Output Voltage Electrical Interfaces To insure reliable encoding performance, the HEDS-6540 three channel encoder requires 2 ...
Page 9
... Mounting Considerations The HEDS-654x/HEDL-654x must be aligned with respect to the optical center (codewheel shaft) as indicated in the following figure. 2 SCREW MOUNTING M2.5 (2-56 UNC-2B) 2 PLCS – EQUALLY SPACED ON 2.62 46.00 (1.811) DIA. (0.103) BOLT CIRCLE ALIGNING PINS 2.39/2.34 DIA. – 0.76 HIGH (0.094/0.092–0.030) 15.88 0.25 (0.010) x (0.625) 45° CHAMFER ...
Page 10
ALIGNMENT TOOL ASSEMBLE COMPONENTS AND MOUNTING SCREWS AND TOOLS AS APPROPRIATE. 2 LOAD ENCODER BASEPLATE ONTO RECEIVING SURFACE (MOTOR END PLATE) WITH MOUNTING SCREW HOLES ALIGNED WITH MATING HOLES. LOAD MOUNTING SCREWS AND LEAVE SLIGHTLY LOOSE. 10 ...
Page 11
CHOOSE CENTERING CYLINDER OR UNDERSIDE LOCATING PINS. CENTERING CYLINDER: LOCATE ENCODER BASEPLATE WITH CENTERING CYLINDER. WHEN IN PLACE, TIGHTEN MOUNTING SCREWS. LOCATING PINS: WITH LOCATING PINS PROPERLY SEATED IN CORRESPONDING RECEIVING HOLES IN ENCODER BASEPLATE, TIGHTEN MOUNTING SCREWS. 4 ...
Page 12
ALLEN WRENCH TO TIGHTEN CODEWHEEL SET SCREW CODEWHEEL GAPPING TOOL WITH CODEWHEEL AND ENCODER MODULE IN PLACE, PLACE CODEWHEEL GAPPING TOOL UNDER CODEWHEEL AS SHOWN. INSERT THE ALLEN WRENCH INTO THE CODEWHEEL SET SCREW AND TIGHTEN. REMOVE ALLEN ...
Page 13
... Ordering Information for 2CH and 3CH Encoder Modules Encoders Metal Codewheel (up to 100 C) HEDS - 65 OUTPUTS THROUGH HOLE 0 – – None 4 – – 13.3 mm (0.525 in HEDS-6500 HEDS-6505 HEDS-6540 HEDS-6545 Encoders Film Codewheel ( HEDM – ...
Page 14
... OUTPUTS THROUGH HOLE 0 – – None 4 – – 13.3 mm (0.525 in HEDL-6540# B HEDL-6545 Ordering Information for HEDS=76XX Centering Tools HEDS-6510 Option 0 DIAMETER 05 – 3/16 in. 06 – 1/4 in. 08 – 3/8 in. 09 – 1/2 in HEDS-6510 Ordering Information for HEDS-65XX Codewheel Gapping Tool HEDS-6511 ...
Page 15
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 ...