ZL50418GKC ZARLINK [Zarlink Semiconductor Inc], ZL50418GKC Datasheet - Page 18
ZL50418GKC
Manufacturer Part Number
ZL50418GKC
Description
Managed 16-Port 10/100 M + 2-Port 1 G Ethernet Switch
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.ZL50418GKC.pdf
(163 pages)
- Current page: 18 of 163
- Download datasheet (2Mb)
If a master receiver does not acknowledge after any byte, then the slave transmitter must release the SDA line to let
the master generate the Stop condition.
2.4.5
After the first byte containing the address, all bytes that follow are data bytes. Each byte must be followed by an
acknowledge bit. Data is transferred MSB first.
2.4.6
Generated by the master. The bus is considered to be free after the Stop condition is generated. The Stop condition
occurs if while the SCL line is High, there is a Low-to-High transition of the SDA line.
The I
slave is the EEPROM memory.
2.5
The synchronous serial interface serves the function of configuring the ZL50418 not at boot time but via a PC. The
PC serves as master and the ZL50418 serves as slave. The protocol for the synchronous serial interface is nearly
identical to the I
transferred.
The unmanaged ZL50418 uses a synchronous serial interface to program the internal registers. To reduce the
number of signals required the register address, command and data are shifted in serially through the D0 pin.
STROBE- pin is used as the shift clock. AUTOFD- pin is used as data return path.
Each command consists of four parts.
•
•
•
•
Any command can be aborted in the middle by sending an ABORT pulse to the ZL50418.
A START command is detected when D0 is sampled high when STROBE- rise and D0 is sampled low when
STROBE- fall.
An ABORT command is detected when D0 is sampled low when STROBE- rise and D0 is sampled high when
STROBE- fall.
START pulse
Register Address
Read or Write command
Data to be written or read back
2
C interface serves the function of configuring the ZL50418 at boot time. The master is the ZL50418, and the
Synchronous Serial Interface
Data
Stop Condition
2
C protocol. The main difference is that there is no acknowledgment bit after each byte of data
Zarlink Semiconductor Inc.
ZL50418
18
Data Sheet
Related parts for ZL50418GKC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
Part Number:
Description:
Satellite Channel Decoder
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Power Factor Controller
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
CMOS/SNOS NVSRAM HIGH PERFORMANCE 8 K x 8 NON-VOLATILE STATIC RAM
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Dual stage IF amplifier for cable tuners
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Synthesized Broadband Converter with Programmable Power
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Cable Tuner Front End LNA with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Front End Power Splitter with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
1.3GHz Dual Wideband Logarithmic Amplifier
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Wide Dynamic Range Image Reject MOPLL
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND PLL FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet: