AM79C971KCW AMD [Advanced Micro Devices], AM79C971KCW Datasheet - Page 99
![no-image](/images/no-image-200.jpg)
AM79C971KCW
Manufacturer Part Number
AM79C971KCW
Description
Manufacturer
AMD [Advanced Micro Devices]
Datasheet
1.AM79C971KCW.pdf
(265 pages)
- Current page: 99 of 265
- Download datasheet (3Mb)
disabling Magic Packet mode. Once either of these
events has occurred indicating that the system has de-
tected the assertion of INTA or an LED pin and is now
awake, the controller will continue polling the receive
and transmit descriptor rings where it left off. Re-initial-
ization should not be performed. If the part is re-initial-
ized, then the descriptor locations will be reset also,
and the Am79C971 controller will not start where it left
off.
If Magic Packet mode is disabled by the deassertion of
SLEEP, then in order to immediately re-enable Magic
Packet mode, the SLEEP pin must remain deasserted
for at least 200 ns before it is reasserted. If Magic
Packet mode is disabled by clearing MPEN, then it may
be immediately re-enabled by setting MPEN back to 1.
The PCI bus interface clock (CLK) is not required to be
running. Both INTA and the LED pins may be used to
indicate the receipt of a Magic Packet frame when the
CLK is stopped. If the system wishes to stop the CLK,
it should do so after enabling the Magic Packet mode.
The clock should be restarted before Magic Packet
mode is disabled if MPEN is being cleared, or the clock
must be restarted right after Magic Packet mode is dis-
abled if SLEEP is being deasserted. Otherwise, the re-
ceive FIFO may overflow if new frames arrive. The
network clock (XTAL) must continue running at all times
while in Magic Packet mode.
CAUTION: To prevent unwanted interrupts from other
active parts of the Am79C971 controller, care must be
taken to mask all likely interruptible events during
Magic Packet mode. An example would be the inter-
rupts from the MII which operate while in Magic Packet
mode.
IEEE 1149.1 (1990) Test Access Port
Interface
An IEEE 1149.1-compatible boundary scan Test Ac-
cess Port is provided for board-level continuity test and
diagnostics. All digital input, output, and input/output
pins are tested. Analog pins, including the AUI differen-
tial driver (DO ) and receivers (DI , CI ), and the crys-
tal input (XTAL1/XTAL2) pins are tested. The T-MAU
drivers TXD , TXP , and receiver RXD are also
tested. The following is a brief summary of the IEEE
1149.1-compatible test functions implemented in the
Am79C971 controller.
Boundary Scan Circuit
The boundary scan test circuit requires four pins (TCK,
TMS, TDI, and TDO), defined as the Test Access Port
(TAP). It includes a finite state machine (FSM), an
instruction register, a data register array, and a power-
on reset circuit. Internal pull-up resistors are provided
Am79C971
for the TDI, TCK, and TMS pins. The boundary scan
circuit remains active during Sleep mode.
TAP Finite State Machine
The TAP engine is a 16-state finite state machine
(FSM), driven by the Test Clock (TCK), and the Test
Mode Select (TMS) pins. An independent power-on
reset circuit is provided to ensure that the FSM is in the
TEST_LOGIC_RESET state at power-up. Therefore,
the TRST is not provided. The FSM is also reset when
TMS and TDI are high for five TCK periods.
Supported Instructions
In addition to the minimum IEEE 1149.1 requirements
(BYPASS, EXTEST, and SAMPLE instructions), three
additional instructions (IDCODE, TRIBYP, and SET-
BYP) are provided to further ease board-level testing.
All unused instruction codes are reserved. See Table
15 for a summary of supported instructions.
Instruction Register and Decoding Logic
After the TAP FSM is reset, the IDCODE instruction is
always invoked. The decoding logic gives signals to
control the data flow in the Data registers according to
the current instruction.
Boundary Scan Register
Each Boundary Scan Register (BSR) cell has two
stages. A flip-flop and a latch are used for the Serial
Shift Stage and the Parallel Output Stage, respectively.
There are four possible operation modes in the BSR
cell shown in Table 16.
Instruc-
tion
Name
EXTEST
IDCODE
SAMPLE
TRIBYP
SETBYP
BYPASS
Table 15. IEEE 1149.1 Supported Instruction
1
2
3
4
Table 16. BSR Mode Of Operation
Instruc-
tion
Code
0000
0001
0010
0011
0100
1111
Description Mode
External Test Test
ID Code
Inspection
Sample
Boundary
Force Float
Control
Boundary To
1/0
Bypass Scan Normal
Summary
System Function
Capture
Update
Shift
Normal
Normal
Normal
Test
Selected
Data
Register
BSR
ID REG
BSR
Bypass
Bypass
Bypass
99
Related parts for AM79C971KCW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AMD-751AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751ACAMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-751](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751AMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-X5-133SFZ](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-X5-133SFZAm5X86? Microprocessor Family
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8131BLC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Hyper Transport PCI-X Tunnel
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8111AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
HyperTransport I/O Hub
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-640AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
System Controller
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-K6](/images/no-image3.png)
Part Number:
Description:
AMD-K6 Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-K6-2E/400AFR](/images/no-image3.png)
Part Number:
Description:
AMD-K6™-2E Embedded Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-8132BLCT](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-K6-IIIE+550ACR](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-766AC](/images/no-image3.png)
Part Number:
Description:
Peripheral Bus Controller
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet: