AM79C971KCW AMD [Advanced Micro Devices], AM79C971KCW Datasheet - Page 77
![no-image](/images/no-image-200.jpg)
AM79C971KCW
Manufacturer Part Number
AM79C971KCW
Description
Manufacturer
AMD [Advanced Micro Devices]
Datasheet
1.AM79C971KCW.pdf
(265 pages)
- Current page: 77 of 265
- Download datasheet (3Mb)
path, RXD(3:0), from the exter nal PHY to the
Am79C971 controller and is synchronous to the rising
edge of RX_CLK.
The receive process starts when RX_DV is asserted.
RX_DV will remain asserted until the end of the receive
frame. The Am79C971 controller requires CRS (Car-
rier Sense) to toggle in between frames in order to re-
ceive them properly. Errors in the currently received
frame are signaled across the MII by the RX_ER pin.
RX_ER can be used to signal special conditions out of
band when RX_DV is not asserted. Two defined out-of-
band conditions for this are the 100BASE-TX signaling
of bad Start of Frame Delimiter and the 100BASE-T4
indication of illegal code group before the receiver has
synched to the incoming data. The Am79C971 control-
ler will not respond to these conditions. All out of band
conditions are currently treated as NULL events. Cer-
tain in band non-IEEE 802.3u-compliant flow control
sequences may cause erratic behavior for the
Am79C971 controller. Consult the switch/bridge/router/
hub manual to disable the in-band flow control se-
quences if they are being used.
MII Network Status Interface
The MII also provides signals that are consistent and
necessary for IEEE 802.3 and IEEE 802.3u operation.
These signals are CRS (Carrier Sense) and COL (Col-
lision Sense). Carrier Sense is used to detect non-idle
activity on the network. Collision Sense is used to indi-
cate that simultaneous transmission has occurred in a
half-duplex network.
MII Management Interface
The MII provides a two-wire management interface so
that the Am79C971 controller can control and receive
status from external PHY devices.
.
Am79C971
Figure 38. Media Independent Interface
Am79C971
4
4
The Am79C971 controller can support up to 31 exter-
nal PHYs attached to the MII Management Interface
with software support and only one such device without
software support.
The Network Port Manager copies the PHYAD after the
Am79C971 controller reads the EEPROM and uses it
to communicate with the external PHY. The PHY ad-
dress must be programmed into the EEPROM prior to
starting the Am79C971 controller. This is necessary so
that the internal management controller can work au-
tonomously from the software driver and can always
know where to ac cess the exter nal PHY. The
Am79C971 controller is unique by offering direct hard-
ware support of the external PHY device without soft-
ware support. The internal PHY is addressed at the last
available MII address of 1Fh. To access the 31 external
PHYs, the software driver must have knowledge of the
external PHY’s address when multiple PHYs are
present before attempting to address it.
The MII Management Interface uses the MII Control,
Address, and Data registers (BCR32, 33, 34) to control
and communicate to the exter nal and inter nal
10BASE-T only PHYs. Am79C971 generates MII man-
agement frames to the external PHY through the MDIO
pin synchronous to the rising edge of the Management
Data Clock (MDC) based on a combination of writes
and reads to these registers. To prevent problems on
the exposed interface, MII management frames will not
be generated when the internal PHY is the target. The
MII only supports internal and external 10BASE-T or
100BASE-T as possible network connections. The in-
ternal AUI and GPSI are not considered part of the MII
and cannot be selected through the MII.
RXD(3:0)
RX_DV
RX_ER
RX_CLK
CRS
COL
TXD(3:0)
TX_EN
TX_ER
TX_CLK
MDC
MDIO
Receive Signals
Network Status Signals
Transmit Signals
Management Port Signals
20550D-41
77
Related parts for AM79C971KCW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AMD-751AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751ACAMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-751](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751AMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-X5-133SFZ](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-X5-133SFZAm5X86? Microprocessor Family
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8131BLC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Hyper Transport PCI-X Tunnel
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8111AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
HyperTransport I/O Hub
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-640AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
System Controller
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-K6](/images/no-image3.png)
Part Number:
Description:
AMD-K6 Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-K6-2E/400AFR](/images/no-image3.png)
Part Number:
Description:
AMD-K6™-2E Embedded Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-8132BLCT](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-K6-IIIE+550ACR](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-766AC](/images/no-image3.png)
Part Number:
Description:
Peripheral Bus Controller
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet: