ZL50051 ZARLINK [Zarlink Semiconductor Inc], ZL50051 Datasheet - Page 22
![no-image](/images/no-image-200.jpg)
ZL50051
Manufacturer Part Number
ZL50051
Description
8 K Channel Digital Switch with High Jitter Tolerance, Single Rate (8 or 16 Mbps), and 64 Inputs and 64 Outputs
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.ZL50051.pdf
(67 pages)
Figure 8 illustrates the input and output frame pulse alignment. The t
pulse, FP8i, and the generated output frame pulse, FP8o. Refer to the “AC Electrical Characteristics”, on page 52.
Note that although this figure shows the traditional setups of the frame pulses and clocks for both ST-BUS and
GCI-Bus configurations, the devices can be configured to accept/generate double-width frame pulses (if the FPW
bit in the Control Register is set) as well as to use the opposite clock edge for frame-boundary determination (using
the C8IPOL and COPOL bits in the Control Register). See the timing diagrams in “AC Electrical Characteristics”, on
page 52 for all of the available configurations.
2.4
To improve the jitter tolerance of the ZL50051/3, a Frame Boundary Discriminator (FBD) circuit was added to the
device. This circuit is enabled by setting the Control Register bit FBDEN to HIGH. By default the FBD is disabled.
The FBD can operate in two modes, as controlled by the FBD_MODE[2:0] bits of the Control Register. When bits
FBD_MODE[2:0] are set to 000
FBD_MODE[2:0] are set to 111
are reserved. These bits are ignored when bit FBDEN is LOW. It is strongly recommended that if bit FBDEN is set
HIGH, bits FBD_MODE[2:0] should be set to 111
To achieve the best jitter tolerance performance, it is also recommended that the input data sampling point be
optimized. In most applications, the optimum sampling point is 1/2 instead of the default 3/4 (it can be changed by
programming all the LIDR and BIDR registers). This will give more allowance for sampling point variations caused
by jitter. There are, however, some cases where data experiences more delay than the timing signals. A common
example occurs when multiple data lines are tied together to form bi-directional buses. The large bus loading may
cause data to be delayed. If this is the case, the optimum sampling point may be 3/4 or 4/4 instead of 1/2. The
optimum sampling point is dependent on the application. The user should optimize the sampling point to achieve
the best jitter tolerance performance.
2.5
Input clock jitter tolerance depends on the data rate. In general, the higher the data rate, the smaller the jitter
tolerance is, because the period of a bit cell is shorter, and the sampling point variation allowance is smaller.
Jitter tolerance can not be accurately represented by just one number. Jitter of the same amplitude but different
frequency spectrum can have different effect on the operation of a device. For example, a device that can tolerate
20 ns of jitter of 10 kHz frequency may only be able to tolerate 10 ns of jitter of 1 MHz frequency. Therefore, jitter
tolerance should be represented as a spectrum over frequency. The highest possible jitter frequency is half of the
carrier frequency. In the case of the ZL50051/3, the input clock is 8.192 MHz, and the jitter associated with this
clock can have the highest frequency component at 4.096 MHz.
For the above reasons, jitter tolerance of the ZL50051/3 has been characterized at 16.384 Mbps. The lower data
rate (8.192 Mbps) will have the same or better tolerance than that of the 16.384 Mbps operation. Tolerance of jitter
of different frequencies are shown in the “AC Electrical Characteristics” section, table “Input Clock Jitter Tolerance”
on page 61. The Jitter Tolerance Improvement Circuit was enabled (Control Register, bit FBDEN set HIGH, and bits
FBD_MODE[2:0] set to 111
3.0
Various registers are used to control the input sampling point (delay) and the output advancement for the Local and
Backplane streams. The following sections explain the details of these offset programming features.
3.1
Control of the Input Bit Delay allows each input stream to have a different frame boundary with respect to the
master frame pulse, FP8i. Each input stream can be individually delayed by up to 7 3/4 bits with a resolution of 1/4
bit of the bit period.
Jitter Tolerance Improvement Circuit - Frame Boundary Discriminator
Input Clock Jitter Tolerance
Input Offsets
Input and Output Offset Programming
B
), and the sampling point was optimized.
B
, the FBD can handle both low frequency and high frequency jitter. All other values
B
, the FBD is set to handle lower frequency jitter only (<8 kHz). When bits
Zarlink Semiconductor Inc.
B
ZL50051/3
to improve the high frequency jitter handling capability.
22
FBOS
is the offset between the input frame
Data Sheet