EPC130 EPC [Espros Photonics corp], EPC130 Datasheet - Page 2

• Manufacturer Part Number: EPC130
• Description: Photo-receiver Amplifier
• Manufacturer: EPC [Espros Photonics corp]

Symbol
Absolute Maximum Ratings
Power Supply Voltage V
Voltage to Any Pin
Maximum Power Dissipation
Storage Temperature Range (T
Lead Temperature solder, 4 sec. (T
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended operating conditions indic -
ate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifica -
tions and test conditions, see Electrical Characteristics.
Note 2: This device is a highly sensitive CMOS ac current amplifier with an ESD rating of JEDEC HBM class 0 (<250V). Handling and as -
sembly of this device should only be done at ESD protected workstations.
Electrical Characteristics
V
© 2011 ESPROS Photonics Corporation
Characteristics subject to change without notice
DD
V
V
I
V
F
V
V
V
C
I
t
R
PDDC
t
I
t
OUT
REC
INIT
IPOR
t
DD
OUT
OUT
POR
PD
PK
PD
OF
PD
rf
PD
= 5.0 V, -40°C < T
Power Supply Current
Sensitivity
Reversed Photodiode
Voltage
Output Offset Voltage
Output Voltage Limits
Output Noise Voltage (RMS) epc130
DC Light Current Range
Photodiode Capacitance
Output Current
Power-up Threshold Voltage
Hysteresis
Power-up Startup Time
Recovery Time
Input Pulse Width at Pin PD
Input pulse slew rate
Photodiode bias resistor
A
Parameter
< +85°C, output load 20 kOhm/20 pF, except as specified
DD
S
)
L
)
epc130
epc131
epc130
epc131
epc131
epc130
epc131
epc130
epc131
epc130
epc131
epc130
epc131
epc130
epc131
(Notes 1, 2)
R1=27k, no photo current
R1=4k7, no photo current
I
I
relative to VDD
I
I
I
I
Refer to section Application Information, Ambient Light
Refer to section Application Information, Photodiode
Capacitance
Push-pull driving capability
The voltage at VDD when the device starts up and the
startup time is running.
On power-up threshold voltage
VDD slew rate >100V/ms
After the reception of a valid pulse current at pin PD
until the output is stable at its operation voltage. R efer
also to Other Parameters section.
Current pulse width at pin PD necessary to generate
an output signal at pin OUT. The input sensitivity is de -
pendent on the input current pulse width (refer to the
section Applications).
Recommended rise and fall time of the current pulse at
pin PD
refer to section 'Application Information, Photodiode
Resistor'
-5.5V to +5.5V
-0.3 to V
300mW
-40°C to +85°C
+260°C
PD
PD
PD
PD
PD
PD
= 80 nA
= 800 nA
= 100 μA
= 3.0 mA
= 100 μA
= 3.0 mA
DD
+0.3V
Conditions/Comments
2
Recommended Operating Conditions
Power Supply Voltage (V
Operating Temperature (T
Humidity (non-condensing)
DD
A
)
)
Min.
-100
1.4
0.3
0.0
3.0
0.5
15
30
Datasheet epc13x analog - V2.1
epc130/epc131
Values
VDD-
Min.
Typ.
-40°
1.55
1.55
0.75
0.75
320
320
400
500
4.0
0.8
1.1
3.5
4.7
+5
35
80
40
90
50
50
27
6
V
Max.
Max.
+100
+85°
DD
www.espros.ch
+95
100
100
5.2
1.2
1.5
1.7
3.0
4.0
1.0
1.5
40
50
50
40
-1.0
Units
Units
mA
mV
mV
mV
mA
ms
pF
μA
kΩ
μs
μs
μs
ns
ns
%
C
V
V
V
V
V
V