X40626V14I Xicor, X40626V14I Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/7/721/xicor_sml.jpg)
X40626V14I
Manufacturer Part Number
X40626V14I
Description
Dual Voltage CPU Supervisor with 64K Serial EEPROM
Manufacturer
Xicor
Datasheet
1.X40626V14I.pdf
(23 pages)
X40626
not block protected can be written. Note that since the
WPEN bit is write protected, it cannot be changed back
Table 1. Write Protect Enable Bit and WP Pin Function
Writing to the Control Register
Changing any of the nonvolatile bits of the control reg-
ister requires the following steps:
– Write a 02H to the Control Register to set the Write
– Write a 06H to the Control Register to set both the
– Write a value to the Control Register that has all the
– A read operation occurring between any of the previ-
REV 1.1.15 2/11/04
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation pro-
ceeded by a start and ended with a stop).
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation proceeded by a start
and ended with a stop).
control bits set to the desired state. This can be rep-
resented as 0xys t01r in binary, where xy are the WD
bits, and rst are the BP bits. (Operation preceeded by
a start and ended with a stop). Since this is a nonvol-
atile write cycle it will take up to 10ms to complete.
The RWEL bit is reset by this cycle and the sequence
must be repeated to change the nonvolatile bits
again. If bit 2 is set to ‘1’ in this third step (0xys t11r)
then the RWEL bit is set, but the WD1, WD0, BP2,
BP1 and BP0 bits remain unchanged. Writing a sec-
ond byte to the control register is not allowed. Doing
so aborts the write operation and returns a NACK.
ous operations will not interrupt the register write
operation.
HIGH
HIGH
LOW
WP
WPEN
X
0
1
Memory Array not
Block Protected
Writes OK
Writes OK
Writes OK
Block Protected
Memory Array
Writes Blocked
Writes Blocked
Writes Blocked
www.xicor.com
to a LOW state; so write protection is enabled as long
as the WP pin is held HIGH.
– The RWEL bit cannot be reset without writing to the
To illustrate, a sequence of writes to the device consist-
ing of [02H, 06H, 02H] will reset all of the nonvolatile
bits in the Control Register to 0. A sequence of [02H,
06H, 06H] will leave the nonvolatile bits unchanged and
the RWEL bit remains set.
SERIAL INTERFACE
Serial Interface Conventions
The device supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter, and the receiving device
as the receiver. The device controlling the transfer is
called the master and the device being controlled is
called the slave. The master always initiates data trans-
fers, and provides the clock for both transmit and
receive operations. Therefore, the devices in this family
operate as slaves in all applications.
Serial Clock and Data
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. See
Figure 5.
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write pro-
tected block.
Block Protect
Writes Blocked
Writes OK
Writes OK
Bits
Characteristics subject to change without notice.
Writes Blocked
WPEN Bit
Writes OK
Writes OK
Protection
Hardware
Software
Software
7 of 23