AN7195 Panasonic Semiconductor, AN7195 Datasheet
AN7195
Available stocks
Related parts for AN7195
AN7195 Summary of contents
Page 1
... ICs for Audio Common Use AN7195K Dual 15 W BTL power IC for car audio Overview The AN7195K is an audio power IC developed for the sound output of car audio (dual 15 W incorporating various protection circuits to pro- tect the IC from destruction by GND-open short-circuit to GND and power supply surge which are the most im- ...
Page 2
... AN7195K Block Diagram 3 Ch.1 GND 4 Ch.1 Out ( ) 2 Ch.1 Out ( ) Pin Descriptions Pin No. Description 1 Power supply 2 Ch.1 output ( ) 3 Grounding (output ch.1) 4 Ch.1 output ( ) 5 Standby 6 Ch.1 input 7 Muting 8 Grounding (sub) Absolute Maximum Ratings Parameter * 2 Supply voltage * 3 Peak supply voltage Supply current *4 Power dissipation * 1 Operating ambient temperature * 1 Storage temperature Note All items are except for the operating ambient temperature and storage temperature ...
Page 3
... THD 4 on/off HPF-on STB THD kHz 4 500 ms 500 ms AN7195K Range Unit 25 C Min Typ Max 120 250 1 10 0.22 0.5 mV[rms 0.07 0 300 0 300 70 ...
Page 4
... AN7195K Terminal Equivalent Circuits Pin No. Equivalent circuit Drive circuit 2 Drive circuit Drive circuit 4 Drive circuit 200 400 Supply voltage pin Supply connection pin Ch.1 output pin ( ) Pre-amp. Ch.1 positive-phase output pin V 6.6 V REF ...
Page 5
... Beep sound signal input pin 15 Input impedance Ch.2 input pin Approx. Approx. Ch. 2 input signal applied pin Input impedance 30 k Ripple filter pin V CC Output current 200 AN7195K Description DC Voltage 2 to10 mV 13 ...
Page 6
... AN7195K Terminal Equivalent Circuits (continued) Pin No. Equivalent circuit 13 1 Drive circuit 13 Drive circuit Drive circuit 14 Drive circuit Usage Notes 1. Always attach an outside heat sink to use the chip. In addition, the outside heat sink must be fastened onto a chassis for use. ...
Page 7
... Ambient temperature Terminal state Open Low High STB 0 V Sub AN7195K 2 C/W 42 C/W 125 150 Table 1 Terminal voltage Power 0 V Standby state 1.0 V Standby state Higher than 3 V Operating state Protection Constant RF circuit current source 3 ...
Page 8
... AN7195K Technical Information (continued) [2] Application note (continued) 2. Oscillation countermeasures 1) In order to increase the oscillation allowance, connect a capacitor and a resistor in series between each output terminal and GND as shown in figure 2. 2) The use of polyester film capacitor having a little fluctuation with temperature and frequency is recommended as the 0.1 F capacitor for oscillation prevention ...
Page 9
... In such a case, insert a capacitor of approx. 0.01 F between the standby terminal and GND. 2) Mute on/off No shock noise is released. Refer to the section on the mute function Constant Protection current source circuit REF 10 k 3.5 k 3.5 k Figure 4 AN7195K 1 3 AN7195K Detection circuit Quick discharge circuit To muting circuit GND of input Figure 5 9 ...
Page 10
... AN7195K Technical Information (continued) [2] Application note (continued) 8. Mute Function 1) The mute-on/off is possible by making pin 7 (the muting terminal) high or low. 2) The muting circuit is as shown in figure 6. The amplifier gain including attenuator block is given in the following equation : Original gain ...
Page 11
... Power supply 2 200 F Standby 2.2 k Mute In(RR In(FR In(RL In(FL S-GND 0.022 F In(FL 2.1 V REF 0.022 2.1 V REF 2 4.7 k 4.7 k 4.7 k 4.7 k Figure 8 AN7195K 300 300 34 dB Figure 7 Out(RR) 0.1 F 0.1 F 2.2 Out(FR) 0.1 F 0.1 F 2.2 Out(RL) 0.1 F 0.1 F 2.2 Out(FL) 0.1 F 0.1 F 2.2 11 ...
Page 12
... AN7195K Technical Information (continued) [2] Application note (continued) 11. Two IC use (continued) 1) Supply terminal Short-circuiting each other, insert an electrolytic capacitor of approx. 2 200 F into the supply terminals. However, if sufficient characteristics of the ripple rejection can not be obtained, use an even larger capacitor or insert a 2 200 F capacitor into each IC. ...