V23836-C18-C363 Infineon Technologies, V23836-C18-C363 Datasheet
V23836-C18-C363
Related parts for V23836-C18-C363
V23836-C18-C363 Summary of contents
Page 1
... Wave solderable and washable with process plug inserted • For distances single mode fiber • 1x9 evaluation board V23806-S84-Z5 available upon request Part Number V23836-C18-C63 V23836-C18-C363 Preliminary Product Information V23836-C18-C63 V23836-C18-C363 Voltage Fiber Optics File: 1161 2004-02-13 ...
Page 2
... Detect that optical data is applied to the optical input V/3.3 V Positive power supply, 5 V/3 V/3 Input Data Inverted transmitter input data Transmitter input data Tx Ground Negative power supply, normally ground Stud Pin Not connected 2 V23836-C18-C63 V23836-C18-C363 Pin Configuration File: 1343 2004-02-13 ...
Page 3
... ATM switches. This transceiver operates at 155.520 Mbit/s from a single power supply ( 3.3 V). The differential data inputs and outputs are DC-coupled and PECL compatible. Preliminary Product Information V23836-C18-C63 V23836-C18-C363 Reach min. max. 0 15,000 ...
Page 4
... We recommend to switch off the transmitter supply ( Preliminary Product Information Automatic Tx Shut-Down Coupling Unit e/o Laser Laser Driver Power Control Rx Coupling Unit Receiver V Tx transmitter input data is applied V23836-C18-C63 V23836-C18-C363 Description o/e Single Mode Fiber o/e File: 1365 V is too high. A reset CC 2004-02-13 ...
Page 5
... With a field strength of 3 V/m, noise IEC 61000-4-3 frequency ranges from 10 MHz to 2 GHz. No effect on transceiver performance between the specification limits. FCC 47 CFR Part 15 Noise frequency range: Class B 30 MHz to 18 GHz; EN 55022 Class B Margins depend on PCB layout and CISPR 22 chassis design. 5 V23836-C18-C63 V23836-C18-C363 Description 2004-02-13 ...
Page 6
... The supply current does not include the load drive current of the CC EE receiver output. Exceeding any one of these values may permanently destroy the device. Preliminary Product Information Symbol – pk- V23836-C18-C63 V23836-C18-C363 Technical Data Limit Values Unit min. max. W 1 ...
Page 7
... 0 1100 C Symbol min –15 O 1260 8 min. and switched on if power supply is above TH 7 V23836-C18-C63 V23836-C18-C363 Technical Data Values Unit typ. max. 70 ° 5.25 3.3 3.6 250 mA –740 mV –1580 mV 1.3 ns 1600 nm Values Unit typ. max. –8 dBm 1360 nm 7 ...
Page 8
... SDD t ASS t DAS V V – –2000 – –1100 V23836-C18-C63 V23836-C18-C363 Technical Data Values typ. max. –36 –28 –31 – 100 80 350 –1580 –740 1 –10 or lower. Measured with into –2 V for data, 510 ...
Page 9
... IEC aperture distance) Complies with 21 CFR 1040.10 and 1040.11 Figure 3 Required Labels Indication of laser aperture and beam Figure 4 Laser Emission Preliminary Product Information FDA Class 1 Laser Product 9 V23836-C18-C63 V23836-C18-C363 Eye Safety 1310 nm 15.6 mW IEC File: 1401 File: 1339 2004-02-13 ...
Page 10
... SerDes supplier. Place R5/6/7/8/10/11 close to Infineon transceiver. 1) Design criterion of the capacitor used is the resonant frequency and its value must be in the order of the nominal data rate. Short trace lengths are mandatory. 10 V23836-C18-C63 V23836-C18-C363 Application Notes SerDes V CC Tx+ ECL/PECL ...
Page 11
... The transceiver contains an automatic shutdown circuit. Reset is only possible if the power is turned off, and then on again. ( Preliminary Product Information termination Rx/ Tx. Further application notes for plane under the module for getting good EMI switched below CC 11 V23836-C18-C63 V23836-C18-C363 Application Notes V or 100 differential 2004-02-13 ...
Page 12
... Package Outlines Tolerance: 0.05 ( 0.002), unless otherwise noted. Dimensions in mm (inches) Figure 6 Preliminary Product Information V23836-C18-C363 12 V23836-C18-C63 Package Outlines File: 1255 2004-02-13 ...
Page 13
... V23836-C18-C63 V23836-C18-C363 Revision History: Previous Version: Page Subjects (major changes since last revision) Edition 2004-02-13 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 München, Germany © Infineon Technologies AG 2004. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics ...