HT82A520R HOLTEK [Holtek Semiconductor Inc], HT82A520R Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
HT82A520R
Manufacturer Part Number
HT82A520R
Description
Full Speed USB 8-Bit OTP MCU with SPI
Manufacturer
HOLTEK [Holtek Semiconductor Inc]
Datasheet
1.HT82A520R.pdf
(72 pages)
HT82A620R
Absolute Maximum Ratings
Supply Voltage ...........................V
Input Voltage..............................V
I
Total Power Dissipation .....................................500mW
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may
Rev.1.00
OL
PA0/SCS
PA1/SCK
PA2/SDI
PA3/SDO
PA4/PWM0
PA5/PWM1
PA6/INT
PA7/TMR
PB0/AN0/PWM2
PB1/AN1
PB2/AN2
PB3/AN3
PB4/AN4
PB5/AN5
PB6/AN6
PB7/AN7
PC0/AN8
PC1/AN9
PC2/AN10
PC3/AN11
PC4/AN12
PC5/AN13
PC6/AN14
PC7/AN15
OSCI
OSCO
RESB
VDD
D -/Data
D +/CLK
V33O
VSS
Total ..............................................................150mA
Pin Name
cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed
in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
I/O
I/O
I/O
I/O
I/O
I/O
O
O
I
I
PB7: I/O or VDDIO
PB0~PB6 power:
NMOS or CMOS
from VDD or
Wake-up
Wake-up
Wake-up
Options
Pull-high
Pull-high
Pull-high
VDDIO
SS
SS
0.3V to V
0.3V to V
DD
SS
Bi-directional 8-bit input/output port. Each bit can be configured as
wake-up input by option (bit option). Software instructions determine
if the pin is output or Schmitt Trigger input. When if output, Configura-
tion option may choose CMOS or NMOS. Configuration options de-
termine if the pins have pull-high resistors.
The TMR and INT are pin-shared with PA6 and PA7, respectively.
PA0~PA3 are shared with SPI function.
PA4~PA5 shared with PWM0~PWM1.
Bi-directional 8-bit input/output port. Software instructions determine
if the pin is a CMOS output or Schmitt Trigger input. Configuration op-
tions determine if the pins have pull-high resistors. PB is pin shared
with the A/D inputs. Once a PB line is selected as an A/D input, using
software control, the I/O function and pull-high resistor are disabled
automatically.
A configuration option determines whether PB7 is an I/O pin or a
power supply pin for PB0~PB6.
A configuration option determines whether the power supply for
PB0~PB6 is sourced from VDD or VDDIO
PB0 shared with PWM2.
Bi-directional 8-bit input/output port. Software instructions determine
if the pin is a CMOS output or Schmitt Trigger input. Configuration op-
tions determine if the pins have pull-high resistors. PC is pin shared
with the A/D inputs. Once a PB line is selected as an A/D input, using
software control, the I/O function and pull-high resistor are disabled
automatically
OSCI, OSCO are connected to an external 6MHz or 12MHz Crys-
tal/resonator, determined by software instructions, for the internal
system clock
Schmitt trigger reset input, active low
Positive power supply
USBD- line
The USB function is controlled by a software control register
USBD+ line
The USB function is controlled by a software control register
3.3V regulator output
Negative power supply, ground
+6.0V
+0.3V
5
Storage Temperature ............................ 50 C to 125 C
Operating Temperature............................. 0 C to 70 C
I
OH
Total............................................................ 100mA
Description
HT82A520R/HT82A620R
October 23, 2009