STR750FXX STMICROELECTRONICS [STMicroelectronics], STR750FXX Datasheet - Page 74
STR750FXX
Manufacturer Part Number
STR750FXX
Description
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.STR750FXX.pdf
(81 pages)
- Current page: 74 of 81
- Download datasheet (2Mb)
Electrical parameters
74/81
General PCB Design Guidelines
To obtain best results, some general design and layout rules should be followed when
designing the application PCB to shield the noise-sensitive, analog physical interface from
noise-generating CMOS logic signals.
●
●
●
●
Software Filtering of Spurious Conversion Results
For EMC performance reasons, it is recommended to filter A/D conversion outliers using
software filtering techniques.
Figure 43. Power supply filtering
Use separate digital and analog planes. The analog ground plane should be connected
to the digital ground plane via a single point on the PCB.
Filter power to the analog power planes. It is recommended to connect capacitors, with
good high frequency characteristics, between the power and ground lines, placing
0.1 µF and optionally, if needed 10 pF capacitors as close as possible to the STR7
power supply pins and a 1 to 10 µF capacitor close to the power source (see
Figure
The analog and digital power supplies should be connected in a star network. Do not
use a resistor, as V
any resistance would cause a voltage drop and a loss of accuracy.
Properly place components and route the signal traces on the PCB to shield the analog
inputs. Analog signals paths should run over the analog ground plane and be as short
as possible. Isolate analog signals from digital signals that may switch while the analog
inputs are being sampled by the A/D converter. Do not toggle digital outputs near the
A/D input being converted.
43).
DDA_ADC
(3.3V or 5.0V)
POWER
SUPPLY
SOURCE
V
DD
1 to 10µF
is used as a reference voltage by the A/D converter and
STR7
DIGITAL NOISE
FILTERING
STR750Fxx STR751Fxx STR752Fxx STR755Fxx
EXTERNAL
NOISE
FILTERING
0.1µF
0.1µF
V
V
V
V
SS
DD_IO
DDA_ADC
SSA_ADC
STR75XX
Related parts for STR750FXX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER IAR STR750
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD DEVELOPMENT LOVE STR750
Manufacturer:
STMicroelectronics
Part Number:
Description:
KIT STARTER HITEX FOR STR750
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD DAUGHTER STR750
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER KEIL FOR STR7/STR9
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVALUATION FOR STR750XF
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER IAR FOR STR7/STR9
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Power Management Modules & Development Tools Compete motr control starter kit
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet: