S-1701A2728-M5T1G SII [Seiko Instruments Inc], S-1701A2728-M5T1G Datasheet - Page 45

• Manufacturer Part Number: S-1701A2728-M5T1G
• Description: HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR WITH RESET FUNCTION
• Manufacturer: SII [Seiko Instruments Inc]

5. S-1701 Series N/ P/ Q types
6. S-1701 Series R/ S/ T types
7. S-1701 Series U/ V/ W types
8. S-1701 Series X/ Y/ Z types
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR WITH RESET FUNCTION
Rev.2.4
The S-1701 Series X / Y / Z types do not provide an ON/OFF function because the ON/OFF pin is connected
to the VIN pin in the circuit.
The SENSE pin is connected to the VIN pin in the internal circuit of the detector block, so the voltage applied
to the VIN pin is monitored and a reset signal is output from the VDOUT pin. The built-in counter timer allows
selection of the release delay time from three settings (X: No delay (60 µs), Y: 50 ms, Z: 100 ms).
The power supply is shared by the regulator block and detector block and supplied from the VIN pin, so care
must be taken concerning the VIN pin input impedance
The S-1701 Series N / P / Q types do not provide an ON/OFF function because the ON/OFF pin is connected
to the VIN pin in the circuit.
The detector block features the external SENSE pin, which allows monitoring of other power supplies. The
SENSE pin is configured only by a resistor, so instantaneous current such as through-type current does not
flow through this pin. This allows precise monitoring of the input power supply by connecting the SENSE pin
to the input power supply even when a resistor (R
VIN pin. The built-in counter timer allows selection of the release delay time from three settings (N: No delay
(60 µs), P: 50 ms, Q: 100 ms).
The power supply is shared by the regulator block and detector block and supplied from the VIN pin, so care
must be taken concerning the VIN pin input impedance
In the S-1701 Series R / S / T types, the VDOUT pin, which is the output pin of the detector, is connected to
the ON/OFF pin of the regulator in the circuit. This allows setting of the regulator to the standby mode at the
same time as the VDOUT pin outputs a RESET signal.
The detector block features an external SENSE pin, which allows monitoring of other power supplies. The
SENSE pin is configured only by a resistor, so instantaneous current such as through-type current does not
flow through this pin. This allows precise monitoring of the input power supply by connecting the SENSE pin
to the input power supply even when a resistor (R
VIN pin. The built-in counter timer allows selection of the release delay time from three settings (R: No delay
(60 µs), S: 50 ms, T: 100 ms).
The power supply is shared by the regulator block and detector block and supplied from the VIN pin, so care
must be taken concerning the VIN pin input impedance
The S-1701 Series U / V / W types do not provide an ON/OFF function because the ON/OFF pin is connected
to the VIN pin in the circuit.
The SENSE pin is connected to the VOUT pin, which is an output pin of the regulator, in the internal circuit of
the detector block, so the output voltage of the regulator (V
the VDOUT pin
No delay (60 µs), V: 50 ms, W: 100 ms).
The power supply is shared by the regulator block and detector block and supplied from the VIN pin, so care
must be taken concerning the VIN pin input impedance
_00
*2
. The built-in counter timer allows selection of the release delay time from three settings (U:
Seiko Instruments Inc.
IN
IN
) is connected between the input power supply and the
) is connected between the input power supply and the
*1
*1
*1
*1
.
.
.
.
OUT
) is monitored and a reset signal is output from
S-1701 Series
45