TDA3681TH PHILIPS [NXP Semiconductors], TDA3681TH Datasheet - Page 2

• Manufacturer Part Number: TDA3681TH
• Description: Multiple voltage regulator with switch and ignition buffer
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
FEATURES
General
Protections
ORDERING INFORMATION
2002 Apr 10
TDA3681J
TDA3681JR
TDA3681TH
Extremely low noise behaviour and good stability with
very small output capacitors
Second supply pin for regulators 3 and 4 to reduce
power dissipation (e.g. via a DC-to-DC converter)
Three V
and 4) and a power switch
Regulator 2, reset and ignition buffer operational during
load dump and thermal shutdown
Combined control pin for switching regulators 1 and 3
Separate control pins for switching regulator 4 and the
power switch
Supply voltage range from 18 to +50 V
Low quiescent current in standby mode (when
regulators 1, 3 and 4 and power switch are switched off
and ignition input is low)
Hold output for low V
switch off)
Hold output when one of regulators 1 and 3 and/or 4 is
out of regulation
Hold output for foldback mode of power switch and
regulators 1, 3 and 4
Hold output for load dump and temperature protection
Reset (push-pull output stage) for regulator 2 and hold
output (open-collector output)
Adjustable reset delay time
High supply voltage ripple rejection
Backup capacitor for regulator 2
One independent ignition buffer (active HIGH).
Reverse polarity safe (down to 18 V without high
reverse current)
Able to withstand voltages up to 18 V at the outputs
(supply line may be short-circuited)
NUMBER
Multiple voltage regulator with switch and
ignition buffer
TYPE
P
-state controlled regulators (regulators 1, 3
HSOP20
DBS17P
DBS17P
NAME
P
(regulators 1, 3 and 4 and power
plastic DIL-bent-SIL power package; 17 leads (lead length 7.7 mm)
plastic DIL-bent-SIL (special bent) power package; 17 leads
(lead length 12 mm)
plastic, heatsink small outline package; 20 leads; low stand-off height
2
DESCRIPTION
GENERAL DESCRIPTION
The TDA3681 is a multiple output voltage regulator with a
power switch and an ignition buffer. It is intended for use in
car radios with or without a microcontroller. The TDA3681
contains the following:
PACKAGE
ESD protection on all pins
Thermal protections
Load dump protection
Foldback current limit protection for regulators 1, 2, 3
and 4
Delayed second current limit protection for the power
switch (at short-circuit)
The regulator outputs and the power switch are
DC short-circuit safe to ground and supply (V
Four fixed voltage regulators with a foldback current
protection (regulators 1, 2, 3 and 4). Regulator 2, which
is intended to supply a microcontroller, also operates
during load dump and thermal shutdown
Regulators 3 and 4 have a second supply pin that can
be connected to a lower supply voltage (>6.5 V) to
reduce the power dissipation
A power switch with protection, operated by a control
input
Reset and hold outputs that can be used to interface
with the microcontroller; the reset signal can be used to
call up the microcontroller
Both supply pins can withstand load dump pulses and
negative supply voltages
Regulator 2, which is in regulation at a backup voltage
above 6.5 V
A provision for the use of a reserve supply capacitor that
will hold enough energy for regulator 2 (5 V continuous)
to allow a microcontroller to prepare for loss of voltage
An ignition input Schmitt trigger with push-pull output
stage.
Product specification
SOT243-3
SOT475-1
SOT418-2
VERSION
TDA3681
P
).