NCP1217 ONSEMI [ON Semiconductor], NCP1217 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
NCP1217
Manufacturer Part Number
NCP1217
Description
Enhanced PWM Current−Mode Controller for High−Power Universal Off−Line Supplies
Manufacturer
ONSEMI [ON Semiconductor]
Datasheet
1.NCP1217.pdf
(18 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NCP1217AD100R2G
Manufacturer:
ON Semiconductor
Quantity:
1 000
Part Number:
NCP1217AD100R2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1217AD65R2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1217AP10
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1217AP100G
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
NCP1217AP65G
Manufacturer:
ON Semiconductor
Quantity:
232
Part Number:
NCP1217D06DR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
NCP1217D133R2G
Manufacturer:
ON Semiconductor
Quantity:
2 000
Company:
Part Number:
NCP1217D65R2G
Manufacturer:
ON Semiconductor
Quantity:
65
Company:
Part Number:
NCP1217P100G
Manufacturer:
SUPERTEX
Quantity:
16 700
Startup Sequence
outlet, the internal current source (typically 7.0 mA) is
biased and charges up the V
on this V
constrained below 16 V, which is the maximum rating on
Pin 6. Figure 17 portrays a typical startup sequence with a
V
Overload Operation
controlled (e.g. wall adapters delivering raw DC level), it is
interesting to implement a true short−circuit protection. A
short−circuit actually forces the output voltage to be at a low
CC
13.5
12.5
10.5
11.5
When the power supply is first powered from the mains
Once the power supply has started, the V
In applications where the output current is purposely not
9.5
regulated at 12.5 V.
Figure 17. A Typical Startup Sequence for
3.00 M
CC
capacitor reaches the VCC
12.8 V
8.00 M
12.8 V/5.6 V
Figure 16. The Current Source Brings V
the NCP1217
t, TIME (sec)
CC
13.0 M
capacitor. When the voltage
+
−
18.0 M
ON
level (typically
REGULATION
CC
NCP1217, NCP1217A
23.0 M
shall be
http://onsemi.com
6 mA or 0
9
CC
12.8 V), the current source turns off and no longer wastes
any power. At this time, the V
controller and the auxiliary supply is supposed to take over
before V
internal arrangement of this structure.
level, preventing a bias current to circulate in the
optocoupler LED. As a result, the auxiliary voltage also
decreases because it also operates in Flyback and thus
duplicates the output voltage, providing the leakage
inductance between windings is kept low. To account for this
situation and properly protect the power supply, NCP1217
hosts a dedicated overload detection circuitry. Once
activated, this circuitry imposes to deliver pulses in a burst
manner with a low duty−cycle. The system auto−recovers
when the fault condition disappears.
maximum until the output voltage reaches its target and the
feedback loop takes over. The auxiliary voltage takes place
after a few switching cycles and self−supplies the IC. In
presence of a short circuit on the output, the auxiliary
voltage will go down until it crosses the undervoltage
lockout level of typically 7.6 V. When this happens,
NCP1217 immediately stops the switching pulses and
unbiases all unnecessary logical blocks. The overall
consumption drops, while keeping the gate grounded, and
the V
5.6 V, the startup source turns−on again and a new startup
sequence occurs, bringing V
to restart. If the default has gone, then the power supply
normally restarts. If not, a new protective burst is initiated,
shielding the SMPS from any runaway. Figure 18 portrays
the typical operating signals in short circuit.
8
6
4
Above 12.8 V and then Turns Off
During the startup phase, the peak current is pushed to the
CC
slowly falls down. As soon as V
CC
CV
collapses below VCC
CC
HV
Aux
CC
CC
toward 12.8 V as an attempt
capacitor only supplies the
min
. Figure 16 shows the
CC
reaches typically