IS24C32C ISSI [Integrated Silicon Solution, Inc], IS24C32C Datasheet
IS24C32C
Available stocks
Related parts for IS24C32C
IS24C32C Summary of contents
Page 1
... The bit stream over the SDA line includes a series of bytes, which identifies a particular Slave device, an instruction, an address within that Slave device, and a series of data, if appropriate. The IS24C32C has a Write Protect pin (WP) to allow blocking of any write instruction transmitted over the bus. JANUARY 2008 ...
Page 2
... IS24C32C FUNCTIONAL BLOCK DIAGRAM Vcc 8 SDA 5 SCL SLAVE ADDRESS REGISTER & COMPARATOR GND 4 nMOS 2 CONTROL LOGIC WORD ADDRESS COUNTER ACK Clock DI/O HIGH VOLTAGE GENERATOR, TIMING & CONTROL EEPROM ARRAY Y DECODER > DATA REGISTER Integrated Silicon Solution, Inc. Rev. B ...
Page 3
... WP is the Write Protect pin. The input level determines if all or none of the array is protected from modifications. Integrated Silicon Solution, Inc. Rev. B 1/04/08 8-pad DFN 8 VCC SCL 5 SDA Write Protection Array Addresses Protected WP GND or floating Vcc VCC SCL GND 4 5 SDA (Top View) IS24C32C None Entire Array 3 ...
Page 4
... Master checks for a High level on SDA.) Standby Mode Power consumption is reduced in standby mode. The IS24C32C will enter standby mode Power-up, and remain in it until SCL or SDA toggles; b) Following the Stop signal write operation is initiated Following any internal write operation. ...
Page 5
... Once all 32 bytes are received and the Stop condition has been sent by the Master, the internal programming cycle begins. At this point, all received data is written to the IS24C32C in a single Write cycle. All inputs are disabled until completion of the internal Write cycle. Acknowledge (ACK) Polling The disabling of the inputs can be used to take advantage of the typical Write cycle time ...
Page 6
... ACK and transmit the 8-bit data byte stored at address location n+1. The Master should not acknowledge the transfer but should generate a Stop condition so the IS24C32C discontinues transmission. If 'n' is the last byte of the memory, the data from location '0' will be transmitted. (Refer to Figure 8. Current Address Read Diagram.) ...
Page 7
... IS24C32C Figure 1. Typical System Bus Configuration SDA SCL Figure 2. Output Acknowledge SCL from Master Data Output from Transmitter Data Output from Receiver Figure 3. START and STOP Conditions SCL SDA Integrated Silicon Solution, Inc. Rev. B 1/04/08 Vcc Master Transmitter/ IS24CXX Receiver ...
Page 8
... IS24C32C Figure 4. Data Validity Protocol SCL SDA Figure 5. Slave Address BIT Figure 6. Byte Write Device R Address T SDA Bus Activity Figure 7. Page Write Device R T Word Address (n) Address T E SDA A Bus Activity R/W 8 Data Change ...
Page 9
... IS24C32C Figure 8. Current Address Read Activity Figure 9. Random Address Read Device R T Address T E SDA A Bus Activity R/W DUMMY WRITE Figure 10. Sequential Read R E Device A Address D SDA A Bus C K Activity R/W Integrated Silicon Solution, Inc. Rev. B ...
Page 10
... Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING RANGE (IS24C32C-2) Range Ambient Temperature Industrial –40°C to +85°C Note: ISSI offers Industrial grade for Commerical applications (0 OPERATING RANGE (IS24C32C-3) Range Ambient Temperature Automotive –40°C to +125°C CAPACITANCE (1,2) Symbol ...
Page 11
... IS24C32C AC WAVEFORMS Figure 11. Bus Timing SCL t SU:STA SDA IN SDA OUT WP Figure 12. Write Cycle Timing SCL 8th BIT SDA WORD n Integrated Silicon Solution, Inc. Rev. B 1/04/ HIGH LOW t HD:DAT t t HD:STA SU:DAT ACK t WR STOP Condition t SU:STO t BUF ...
Page 12
... IS24C32C DC ELECTRICAL CHARACTERISTICS Symbol Parameter V 1 Output Low Voltage Output Low Voltage OL V Input High Voltage IH V Input Low Voltage IL I Input Leakage Current LI I Output Leakage Current LO Notes: V min and V max are reference only and are not tested ...
Page 13
... IS24C32C AC ELECTRICAL CHARACTERISTICS Symbol Parameter f SCL Clock Frequency SCL (1) T Noise Suppression Time t Clock Low Period Low t Clock High Period High t Bus Free Time Before New Transmission BUF t Start Condition Setup Time SU:STA t Stop Condition Setup Time SU:STO t Start Condition Hold Time ...
Page 14
... IS24C32C-2GLI IS24C32C-2ZLI IS24C32C-2SLI* ORDERING INFORMATION Automotive Range: -40°C to +125°C, Lead-free Voltage Range Part Number 2.5V IS24C32C-3PLA3* to 5.5V IS24C32C-3GLA3 IS24C32C-3ZLA3 * Please contact ISSI Sales Rep for availability. 14 Package 8-pad 2x3 mm DFN 8-pin 300-mil Plastic DIP 8-pin 150-mil SOIC (JEDEC STD) 8-pin 3x4.4 mm TSSOP ...
Page 15
... IS24C32C Dual Flat No-Lead Package Code: D (8-pad) D Pad 1 index area DFN MILLIMETERS Sym. Min. Nom. Max. N0. Pad 8 D 2.00 BSC E 3.00 BSC D2 1.50 — 1.75 E2 1.60 — 1.90 A 0.70 0.75 0.80 A1 0.0 0.02 0.05 A2 — — 0.75 A3 0.20 REF L 0.30 0.40 0.50 e 0.50 BSC b 0.18 0.25 0.30 Integrated Silicon Solution, Inc. Rev. B 1/04/ (3) tie bars e (6X) e (6X 1.50 REF. ...
Page 16
... IS24C32C 300-mil Plastic DIP Package Code: N FOR 32-PIN ONLY MILLIMETERS Sym. Min. Max. Min. N0. Leads 8 A 4.57 3.68 0.145 A1 — 0.38 0.015 B 0.56 0.36 0.014 B1 1.52 1.14 0.045 B2 1.17 0.81 0.032 C 0.33 0.20 0.008 D 9.12 9.53 0.359 E 7.62 8.26 0.300 E1 6.20 6.60 0.244 e A 8.13 9.65 0.320 e 2.54 BSC — L 3.18 0.125 S 0.64 0.762 0.025 Notes: INCHES 1. Controlling dimension: inches, unless otherwise specified. ...
Page 17
... IS24C32C 150-mil Plastic SOP Package Code 150-mil Plastic SOP (G, GR) Symbol Min Max Ref. Std. Inches No. Leads 8 A — 0.068 A1 0.004 0.009 B 0.013 0.020 C 0.007 0.010 D 0.189 0.197 E 0.150 0.157 H 0.228 0.245 e 0.050 BSC L 0.020 0.035 Integrated Silicon Solution, Inc. ...
Page 18
... IS24C32C Thin Shrink Small Outline TSSOP Package Code pin, 14 pin TSSOP (Z) Ref. Std. JEDEC MO-153 No. Leads 8 Millimeters Symbol Min Max A — 1.20 A1 0.05 0.15 A2 0.80 1.05 B 0.19 0.30 C 0.09 0.20 D 2.90 3.10 E1 4.30 4.50 E 6.40 BSC e 0.65 BSC L 0.45 0.75 α — 8° N Ref. Std. No. Leads Millimeters Inches ...
Page 19
... IS24C32C Plastic MSOP Package Code Plastic MSOP (S) Ref. Std. JEDEC MO 187 No. Leads 8 (120 mil) Inches Millimeters Symbol Min Max Min A 0.038 0.043 0.97 A1 0.002 0.006 0.05 B 0.010 0.016 0.25 C 0.005 0.009 0.13 D 0.114 0.122 2.90 E 0.193 BSC 4.90 BSC E1 0.114 0.122 2.90 e 0.0256 BSC 0.65 BSC L — ...
Page 20
... IS24C32C REVISION HISTORY Rev. Date A April 2007 B January 2008 20 Description Draft version Initial version for product launch Integrated Silicon Solution, Inc. Rev. B 1/04/08 ...