M58BW016DB7T3FF NUMONYX [Numonyx B.V], M58BW016DB7T3FF Datasheet - Page 35
M58BW016DB7T3FF
Manufacturer Part Number
M58BW016DB7T3FF
Description
16 Mbit (512 Kbit x 32, boot block, burst) 3 V supply Flash memories
Manufacturer
NUMONYX [Numonyx B.V]
Datasheet
1.M58BW016DB7T3FF.pdf
(70 pages)
- Current page: 35 of 70
- Download datasheet (2Mb)
M58BW016DT, M58BW016DB, M58BW016FT, M58BW016FB
5.3
5.4
5.5
Erase status (bit 5)
The erase status bit can be used to identify if the memory has failed to verify that the block
has erased correctly. The erase status bit should be read once the program/erase controller
status bit is High (program/erase controller inactive).
When the erase status bit is set to ‘0’, the memory has successfully verified that the block
has erased correctly. When the erase status bit is set to ‘1’, the program/erase controller has
applied the maximum number of pulses to the block and still failed to verify that the block
has erased correctly.
Once set to ‘1’, the erase status bit can only be reset to ‘0’ by a Clear Status Register
command or a hardware reset. If set to ‘1’ it should be reset before a new Program or Erase
command is issued, otherwise the new command will appear to fail.
Program status (bit 4)
The program status bit is used to identify a program failure. Bit4 should be read once the
program/erase controller status bit is High (program/erase controller inactive).
When bit4 is set to ‘0’ the memory has successfully verified that the device has programmed
correctly. When bit4 is set to ‘1’ the device has failed to verify that the data has been
programmed correctly.
Once set to 1’, the program status bit can only be reset to ‘0’ by a Clear Status Register
command or a hardware reset. If set to ‘1’ it should be reset before a new Program or Erase
command is issued, otherwise the new command will appear to fail.
V
The V
program and erase operations. The V
or erase operation. Indeterminate results can occur if V
program or erase operation.
When the V
voltage; when the V
lockout voltage, V
Once set to ‘1’, the V
command or a hardware reset. If set to ‘1’ it should be reset before a new Program or Erase
command is issued, otherwise the new command will appear to fail.
PP
PP
status (bit 3)
status bit can be used to identify an invalid voltage on the V
PP
status bit is set to ‘0’, the voltage on the V
PPLK
PP
PP
.
status bit is set to ‘1’, the V
status bit can only be reset to ‘0’ by a Clear Status Register
PP
pin is only sampled at the beginning of a program
PP
pin has a voltage that is below the V
PP
PP
becomes invalid during a fast
pin was sampled at a valid
PP
pin during fast
Status register
35/70
PP
Related parts for M58BW016DB7T3FF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Numonyx Wireless Flash Memory (W18)
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
Numonyx StrataFlash Wireless Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
8 Mbit, low voltage, Page-Erasable Serial Flash memory with byte alterability and a 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (8 Mb ×16, multiple bank, multilevel interface, burst) 1.8 V supply, secure Flash memories
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
Wireless Flash Memory (W18/W30 SCSP)
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
StrataFlash® Cellular Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (8 Mb x 16, multiple bank, page, dual boot) 3 V supply Flash memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 8:24, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 16:16, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet: