W981216 WINBOND [Winbond], W981216 Datasheet - Page 13

no-image

W981216

Manufacturer Part Number
W981216
Description
2M x 16 bit x 4 Banks SDRAM
Manufacturer
WINBOND [Winbond]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
W981216AH-75
Quantity:
1 000
Part Number:
W981216AH-75
Quantity:
1 000
Part Number:
W981216AH-75
Manufacturer:
TI
Quantity:
5 600
Part Number:
W981216BH-7
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Part Number:
W981216BH-75
Manufacturer:
WINBOND
Quantity:
37
Part Number:
W981216BH-75
Manufacturer:
MAXIM
Quantity:
131
Part Number:
W981216DH-7
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Part Number:
W981216DH-75
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Company:
Part Number:
W981216DH-75
Quantity:
266
If A10 is set to high when the Read or Write Command is issued, then the auto-precharge function is entered. During auto-
precharge, a Read Command will execute as normal with the exception that the active bank will begin to precharge automatically
before all burst read cycles have been completed. Regardless of burst length, it will begin a certain number of clocks prior to the
end of the scheduled burst cycle. The number of clocks is determined by CAS latency.
A Read or Write Command with auto-precharge can not be interrupted before the entire burst operation is completed. Therefore,
use of a Read, Write, or Precharge Command is prohibited during a read or write cycle with auto-precharge. Once the precharge
operation has started, the bank cannot be reactivated until the Precharge time (t
command is illegal if the burst is set to full page length. If A10 is high when a Write Command is issued, the Write with Auto-
Precharge function is initiated. The SDRAM automatically enters the precharge operation one clock delay from the last burst
write cycle. This delay is referred to as Write t
satisfied. This is referred to as t
interval between the Bank Activate Command and the beginning of the internal precharge operation must satisfy t
The Precharge Command is used to precharge or close a bank that has been activated. The Precharge Command is entered when
CS, RAS and WE are low and CAS is high at the rising edge of the clock. The Precharge Command can be used to precharge
each bank separately or all banks simultaneously. Three address bits, A10, A12, and A13, are used to define which bank(s) is to
be precharged when the command is issued. After the Precharge Command is issued, the precharged bank must be reactivated
before a new read or write access can be executed. The delay between the Precharge Command and the Activate Command must
be greater than or equal to the Precharge time (t
The Self Refresh Command is defined by having CS, RAS, CAS and CKE held low with WE high at the rising edge of the clock.
All banks must be idle prior to issuing the Self Refresh Command. Once the command is registered, CKE must be held low to
keep the device in Self Refresh mode. When the SDRAM has entered Self Refresh mode all of the external control signals, except
CKE, are disabled. The clock is internally disabled during Self Refresh Operation to save power. The device will exit Self
Refresh operation after CKE is returned high. A minimum delay time is required when the device exits Self Refresh Operation
and before the next command can be issued. This delay is equal to the RAS cycle time plus the Self Refresh exit time.
The Power Down mode is initiated by holding CKE low. All of the receiver circuits except CKE are gated off to reduce the
power. The Power Down mode does not perform any refresh operations, therefore the device can not remain in Power Down
mode longer than the Refresh period (t
The Power Down mode is exited by bringing CKE high. When CKE goes high, a No Operation Command is required on the next
rising clock edge, depending on t
t
Auto-Precharge Command
Precharge Command
Self Refresh Command
Power Down Mode
CK
Revision 1.0
(min).
DAL
CK
. The input buffers need to be enabled with CKE held high for a period equal to t
, Data-in to Active delay (t
REF
) of the device.
DPL
RP
. The bank undergoing auto-precharge can not be reactivated until t
).
- 13 -
DAL
= t
2M x 16 bit x 4 Banks SDRAM
DPL
+ t
RP
). When using the Auto-precharge Command, the
RP
) has been satisfied. Issue of Auto-Precharge
Publication Release Date: March, 1999
W981216AH
RAS
(min).
DPL
and t
CES
(min) +
RP
are

Related parts for W981216