93AA46/SM MICROCHIP [Microchip Technology], 93AA46/SM Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
93AA46/SM
Manufacturer Part Number
93AA46/SM
Description
1K/2K/4K 1.8V Microwire Serial EEPROM
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.93AA46SM.pdf
(22 pages)
93AA46/56/66
2.0
When the ORG pin is connected to V
organization is selected.
ground, the (x8) organization is selected. Instructions,
addresses and write data are clocked into the DI pin on
the rising edge of the clock (CLK). The DO pin is nor-
mally held in a high-Z state except when reading data
from the device, or when checking the Ready/Busy
status during a programming operation. The Ready/
Busy status can be verified during an erase/write
operation by polling the DO pin; DO low indicates that
programming is still in progress, while DO high
indicates the device is ready. The DO will enter the
high-Z state on the falling edge of the CS.
2.1
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device opera-
tion (read, write, erase, EWEN, EWDS, ERAL, and
WRAL). As soon as CS is high, the device is no longer
in the Standby mode.
An instruction following a Start condition will only be
executed if the required amount of opcode, address
and data bits for any particular instruction is clocked in.
After execution of an instruction (i.e., clock in or out of
the last required address or data bit) CLK and DI
become “don't care” bits until a new Start condition is
detected.
2.2
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation, if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of A0,
the higher the voltage at the Data Out pin.
2.3
During power-up, all programming modes of operation
are inhibited until V
1.4V. During power-down, the source data protection
circuitry acts to inhibit all programming modes when
V
DS20067J-page 6
CC
has fallen below 1.4V at nominal conditions.
FUNCTIONAL DESCRIPTION
Start Condition
DI/DO
Data Protection
CC
has reached a level greater than
When it is connected to
CC
, the (x16)
preceded by an Erase/Write Enable (EWEN) instruction.
accidental data disturb, the EWDS instruction can be used
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before any ERASE or WRITE instruction can
be executed.
2.4
The READ instruction outputs the serial data of the
addressed memory location on the DO pin. A dummy
zero bit precedes the 16-bit (x16 organization) or 8 bit
(x8 organization) output string. The output data bits will
toggle on the rising edge of the CLK and are stable
after the specified time delay (T
possible when CS is held high. The memory data will
automatically cycle to the next register and output
sequentially.
2.5
The 93AA46/56/66 power up in the Erase/Write Disable
(EWDS) state.
Once the EWEN instruction is executed, programming
remains enabled until an EWDS instruction is executed or
V
to disable all erase/write functions and should follow all
programming operations. Execution of a READ instruction
is independent of both the EWEN and EWDS instructions.
2.6
The ERASE instruction forces all data bits of the
specified address to the logical “1” state. CS is brought
low following the loading of the last address bit. This
falling edge of the CS pin initiates the self-timed
programming cycle.
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (T
ming is still in progress. DO at logical “1” indicates that
the register at the specified address has been erased
and the device is ready for another instruction.
The erase cycle takes 4 ms per word typical.
CC
is removed from the device. To protect against
CSL
Read
Erase/Write Enable and Disable
(EWEN, EWDS)
Erase
). DO at logical “0” indicates that program-
All programming modes must be
2004 Microchip Technology Inc.
PD
). Sequential read is