MCP6292 MICROCHIP [Microchip Technology], MCP6292 Datasheet - Page 15

no-image

MCP6292

Manufacturer Part Number
MCP6292
Description
1.0 mA, 10 MHz Rail-to-Rail Op Amp
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP6292-E/MS
Manufacturer:
MICROCHIP
Quantity:
16 700
Part Number:
MCP6292-E/MS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MCP6292-E/MS
Quantity:
720
Part Number:
MCP6292-E/P
Manufacturer:
Microchip
Quantity:
6 974
Part Number:
MCP6292-E/SN
Manufacturer:
Nuvoton
Quantity:
107
Part Number:
MCP6292-E/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP6292-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP6292-I/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP6292IDR
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
MCP6292T-E/MS
Manufacturer:
MICROCHIP
Quantity:
30 000
Part Number:
MCP6292T-E/MS
0
Part Number:
MCP6292T-E/SN
Manufacturer:
MICROCHIP
Quantity:
12 000
4.9
4.9.1
The MCP6291/1R/2/3/4/5 op amp can be used in
active-filter applications.
third-order, multiple feedback low-pass filter that can be
used as an anti-aliasing filter.
FIGURE 4-8:
Pass Filter.
This filter, and others, can be designed using
Microchip’s Filter design software. Refer to Section 5.0
“Design Aids”
4.9.2
Figure 4-9
taic mode for high precision. The resistor R converts
the diode current I
is used to limit the bandwidth or to stabilize the circuit
against the diode’s capacitance (it is not always
needed).
FIGURE 4-9:
© 2007 Microchip Technology Inc.
V
light
IN
V
DD
/2
V
Application Circuits
R
DD
I
C
shows a photodiode biased in the photovol-
D
1
MULTIPLE FEEDBACK LOW-PASS
FILTER
PHOTODIODE AMPLIFIER
1
/2
D
to the voltage V
R
MCP6291
3
Multiple Feedback Low-
Photodiode Amplifier.
Figure 4-8
MCP6291
R
C
2
3
C
R
shows an inverting,
OUT
R
. The capacitor
C
4
4
V
OUT
V
OUT
4.9.3
The MCP6295 provides the flexibility of Low-power
mode for dual op amps in an 8-pin package. The
MCP6295 eliminates the added cost and space in
battery-powered applications by using two single op
amps with Chip Select lines or a 10-pin device with one
Chip Select line for both op amps. Since the two op
amps are internally cascaded, this device cannot be
used in circuits that require active or passive elements
between the two op amps. However, there are several
applications where this op amp configuration with
Chip Select line becomes suitable. The circuits below
show possible applications for this device.
4.9.3.1
With the cascaded op amp configuration, op amp B can
be used to isolate the load from op amp A. In applica-
tions where op amp A is driving capacitive or low
resistance loads in the feedback loop (such as an
integrator circuit or filter circuit), the op amp may not
have sufficient source current to drive the load. In this
case, op amp B can be used as a buffer.
FIGURE 4-10:
Buffer.
MCP6291/1R/2/3/4/5
A
CASCADED OP AMP
APPLICATIONS
Load Isolation
MCP6295
Isolating the Load with a
CS
B
DS21812E-page 15
Load
V
OUTB

Related parts for MCP6292