AT83C26_07 ATMEL [ATMEL Corporation], AT83C26_07 Datasheet - Page 60
AT83C26_07
Manufacturer Part Number
AT83C26_07
Description
Multiple Smart Card Reader Interface With Power Management
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT83C26_07.pdf
(77 pages)
- Current page: 60 of 77
- Download datasheet (738Kb)
Table 42. DCDCB (Config Interface B Byte 2)
60
SHUTDOWNB
Bit Number
1-0
7
6
5
4
3
2
7
AT83C26
VDCB_INT
Bit Mnemonic
SHUTDOWNB
STEPREGB
VDCB_INT
VDCB_OK
VDCB[1:0]
ICCADJB
0
6
Reset value = 0x 0000 0000
Description
Shutdown DCDCB
Set this bit to reduce the power consumption. An automatic de-activation sequence will be done.
Clear this bit to enable VDCB.
The reset value is 0.
DC/DC B voltage interrupt
This bit is set when VCARD_OKB bit is set.
This bit is cleared when read by the micro controller.
The reset value is 0.
DC/DC B Voltage Status
The reset value is 0.
This bit must be always at 0.
CI
This bit controls the DC/DCB sensitivity to any overflow current.
Set this bit to decrease the DC/DCB sensitivity (CI
Clear this bit to have a normal configuration.
The reset value is 0.
DC/DC B Step-up Regulator Mode
Set this bit to permanently disable the step-up converter (CVCC is stable only if VCC is sufficiently higher
than CVCC). This bit must always be set if no external self is used.
Clear this bit to enable the automatic step-up converter (CVCC is stable even if VCC is not higher than
CVCC).
The reset value is 0.
VDCB[1:0] = 00: 0V
VDCB[1:0] = 01: 2.2V (for Class C)
VDCB[1:0] = 10: 3.2V (for Class B and C)
VDCB[1:0] = 11: 5.2V (for Class A, B and C)
No card deactivation is performed when the voltage is changed. The voltage must be set higher than the
voltage of all the active cards. If a Class A card is deactivated and the remaining cards are in Class B or C,
VDCB can be reduced to 3.2V to reduce power consumption. If a Class B card is deactivated and the
remaining cards are in Class C, VDCB can be reduced to 2.2V to reduce power consumption.It is not reset
when cards are deactivated. It must be cleared by the micro controller to stop DC/DC B (e.g. to reduce power
consumption).
The reset value is 00.
This bit is set by the DCDC when the output voltage remains within the voltage range specified by VDCB[1:0]
bits. It is recommended to wait for this bit to be set before activating a card at the corresponding voltage.
It is cleared otherwise.
DC/DC B Voltage Selection
VDCB_OK
CC
overflow adjust
5
4
0
ICCADJB
3
CC_ovf
is increased by about 20%).
STEPREGB
2
VDCB1
1
7511D–SCR–02/07
VDCB0
0
Related parts for AT83C26_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
SMART CARD READER INTERFACE WITH POWER MANAGEMENT
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Multiple Smart Card Reader Interface With Power Management
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: