TDA9882HN NXP [NXP Semiconductors], TDA9882HN Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
TDA9882HN
Manufacturer Part Number
TDA9882HN
Description
Alignment-free multistandard vision and QSS FM sound IF PLL demodulator
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.TDA9882HN.pdf
(45 pages)
Philips Semiconductors
[4]
[5]
[6]
[7]
[8]
[9]
[10] Sound carrier on; f
[11] Conditions: video signal, grey level and negative modulation.
[12] AC load; C
[13] The response time is valid for a VIF input level range from 200 V to 70 mV.
[14] To match the AFC output signal to different tuning systems a current source output is provided. The test circuit is given in
[15] The tolerance of the reference frequency determines the accuracy of the VIF AFC, FM demodulator center frequency and maximum
[16] For negative modulation no DC load at pin QSSO is allowed. Positive modulation mode will be activated by the application of a 2.2 k
[17] SIF input level is 10 mV (RMS); VIF input level is 10 mV (RMS) unmodulated.
[18] Measured with an FM deviation of 25 kHz and the typical AF output voltage of 500 mV (RMS). For handling a frequency deviation of
[19] The lower limit of the audio bandwidth depends on the value of the capacitor at pin AFD. A value of C
[20] For all S/N measurements the used VIF modulator has to meet the following specifications:
9397 750 13507
Product data sheet
Loop bandwidth BL = 70 kHz (damping factor d = 1.9; calculated with sync level within gain control range). Calculation of the VIF PLL
filter can be done by use of the following formula:
where:
K
R is the loop resistor; C is the loop capacitor; BL
V
Condition: luminance range (5 steps) from 0 % to 100 %.
S/N
I and D/K standard). Noise analyzer setting: 200 kHz high-pass and SC-trap switched on.
The intermodulation figures are defined for:
a) f = 1.1 MHz (referenced to black and white signal) as
b) f = 3.3 MHz (referenced to color carrier) as
Modulation Vestigial Side-Band (VSB); sound carrier off; f
20 dB); loop bandwidth BL = 70 kHz.
BL = 70 kHz.
carrier traps (see
AFC slope (voltage per frequency) can be changed by resistors R1 and R2.
FM deviation.
resistor between pin QSSO and ground.
more than 55 kHz, the AF output signal has to be reduced in order to avoid clipping (THD < 1.5 %) by means of a resistor R
external application at pin AFD (see
f
a) Incidental phase modulation for black-to-white jump less than 0.5 degrees.
b) QSS AF performance, measured with the television demodulator AMF2 (audio output, weighted S/N ratio) better than 60 dB (at
c) Picture-to-sound carrier ratio PC/SC
BL
d
AF( 3dB)
O
i(VIF)
=
is the VCO steepness
deviation 27 kHz) for 6 kHz sine wave black-to-white video modulation.
–
W(video)
3dB
1
-- - R K
2
= 10 mV (RMS); f = 1 MHz (VCO frequency offset related to picture carrier frequency); white picture video modulation.
=
20 Hz and C
L
is the ratio of black-to-white amplitude to the black level noise voltage (RMS value measured on pin CVBS). B = 5 MHz (B/G,
----- -K
2
< 20 pF and R
O
1
K
D
O
C
Figure 12
K
video
,
D
R
AF
= 10 kHz to 10 MHz. Measurements taken with SAW filter M1963M (sound shelf: 20 dB); loop bandwidth
, valid for d
= 220 nF leads to f
L
rad
------ -
to
V
> 1 k . The sound carrier frequencies (depending on TV standard) are attenuated by the integrated sound
Figure
or
Figure 22
2
17; H(s) is the absolute value of transfer function).
1.2
1
Hz
------ -
V
= 13 dB (transmitter).
AF( 3dB)
; K
and
D
IM
3dB
Rev. 01 — 16 November 2004
is the phase detector steepness
Figure
=
is the loop bandwidth for 3 dB; d is the damping factor.
Multistandard vision and QSS FM sound IF PLL demodulator
40 Hz.
20
video
23).
log
IM
> 0.5 MHz. Measurements taken with SAW filter M1963M (sound shelf:
=
V
---------------------------------- -
V
0
0
20
at 4.4 MHz
at 3.3 MHz
log
V
---------------------------------- -
V
0
0
at 4.4 MHz
at 1.1 MHz
------ -
rad
A
;
+
3.6 dB
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
AF
= 470 nF leads to
TDA9882
Figure
x
with
25 of 45
9. The