CDP68HC68T1W INTERSIL [Intersil Corporation], CDP68HC68T1W Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
CDP68HC68T1W
Manufacturer Part Number
CDP68HC68T1W
Description
CMOS Serial Real-Time Clock With RAM and Power Sense/Control
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.CDP68HC68T1W.pdf
(24 pages)
CLK OUT
Clock output pin. One of seven frequencies can be selected
(or this output can be set low) by the levels of the three
LSB’s in the Clock-Control Register. If a frequency is
selected, it will toggle with a 50% duty cycle except 2Hz in
the 50Hz time base mode. (Ex, if 1Hz is selected, the output
will be high for 500ms and low for the same period). During
power-down operation (bit 6 in Interrupt Control Register set
to “1”), the clock-output pin will be set low.
CPUR
CPU reset output pin. This pin functions as an N-Channel
only, open-drain output and requires an external pull-up
resistor.
INT
Interrupt output pin. This output is driven from a single NFET
pulldown transistor and must be tied to an external pull-up
resistor. The output is activated to a low level when:
1. Power-sense operation is selected (B5 = 1 in Interrupt
2. A previously set alarm time occurs. The alarm bit in the
3. A previously selected periodic interrupt signal activates.
The Status Register must be read to set the Interrupt output
high after the selected periodic interval occurs. This is also
true when conditions 1 and 2 activate the interrupt. If power
down had been previously selected, the interrupt will also
reset the power-down functions.
SCK, MOSI, MISO
See Serial Peripheral Interface (SPI) section in this data sheet.
CE
A positive chip-enable input. A low level at this input holds the
serial interface logic in a reset state. This pin is also used for
the watchdog function.
FIGURE 6. POWER-UP FUNCTIONAL DIAGRAM (INITIATED BY
Control Register) and a power failure occurs.
Status Register and interrupt-out signal are delayed
30.5 s when 32kHz operation is selected and 15.3 s for
2MHz and 7.6 s for 4MHz.
A RISE IN VOLTAGE ON THE “V
V
BATT
V
SYS
REAL-TIME CLOCK
INTERFACE
CDP68HC68T1
SERIAL
CPUR
OUT
PSE
CLK
SYS
” PIN)
MISO
MOSI
CDP68HC68T1
9
V
The negative power-supply pin that is connected to ground.
PSE
Power-supply enable output pin. This pin is used to control
power to the system. The pin is set high when:
1. V
2. An interrupt occurs.
3. A power-on reset (if V
The PSE pin is set low by writing a high into bit 6 (power-
down bit) in the Interrupt Control Register.
POR
Power-on reset. A Schmitt-trigger input that generates a
power-on internal reset signal using an external R-C net-
work. Both control registers and frequency dividers for the
oscillator and line input are reset. The Status Register is
reset except for the first time up bit (B4), which is set.
Single supply or battery backup operation is selected at the
end of POR.
LINE
This input is used for two functions. When not used it
should be connected to V
function utilizes the input signal as the frequency source for
the timekeeping counters. This function is selected by
setting bit 6 in the Clock Control Register. The second
function enables the line input to sense a power failure.
Threshold detectors operating above and below V
an AC voltage loss. Bit 5 must be set to “1” in the Interrupt
Control Register and crystal or external clock source
operation is required. Bit 6 in the Clock Control Register
must be low to select XTAL operation.
Oscillator Circuit
The CDP68HC68T1 has an on-board 150K resistor that is
switched in series with its internal inverter when 32kHz is
selected via the Clock Control Register. Note: When first
powered up the series resistor is not part of the oscillator
circuit. (The CDP68HC68T1 sets up for a 4MHz oscillator).
SS
placed low by a system failure.
SYS
rises above the V
SYS
DD
BATT
is a logic high).
via a 10k
voltage after V
resistor. The first
DD
SYS
sense
was