PCA8575BQ PHILIPS [NXP Semiconductors], PCA8575BQ Datasheet
PCA8575BQ
Available stocks
Related parts for PCA8575BQ
PCA8575BQ Summary of contents
Page 1
PCA8575 Remote 16-bit I/O expander for I Rev. 01 — 30 November 2006 1. General description The PCA8575 provides general purpose remote I/O expansion for most microcontroller families via the two-line bidirectional I The device consists of a 16-bit quasi-bidirectional ...
Page 2
... Type number Topside Package mark Name PCA8575D PCA8575D SO24 PCA8575DB PCA8575DB SSOP24 PCA8575DK PCA8575 SSOP24 PCA8575PW PCA8575PW TSSOP24 PCA8575BQ 8575 DHVQFN24 plastic dual in-line compatible thermal enhanced very thin quad PCA8575BS 8575 HVQFN24 [1] Also known as QSOP24. 5. Block diagram INT AD0 AD1 AD2 SCL ...
Page 3
NXP Semiconductors data from Shift Register data to Shift Register Fig 2. Simplified schematic diagram of P00 to P17 6. Pinning information 6.1 Pinning INT AD1 AD2 P00 P01 P02 P03 P04 P05 P06 P07 V Fig 3. Pin configuration ...
Page 4
... 002aac673 Fig 6. Pin configuration for SSOP24 terminal 1 index area AD1 2 AD2 3 4 P00 P01 5 P02 6 PCA8575BQ 7 P03 8 P04 P05 9 P06 10 11 P07 Transparent top view Fig 8. Pin configuration for DHVQFN24 © NXP B.V. 2006. All rights reserved ...
Page 5
NXP Semiconductors 6.2 Pin description Table 2. Symbol INT AD1 AD2 P00 P01 P02 P03 P04 P05 P06 P07 V SS P10 P11 P12 P13 P14 P15 P16 P17 AD0 SCL SDA V DD [1] HVQFN and DHVQFN package die ...
Page 6
NXP Semiconductors 7. Functional description Refer to 7.1 Device address Following a START condition, the bus master must send the address of the slave it is accessing and the operation it wants to perform (read or write). The address of ...
Page 7
NXP Semiconductors 8. I/O programming 8.1 Quasi-bidirectional I/O architecture The PCA8575’s 16 ports (see as input or output ports. Input data is transferred from the ports to the microcontroller in the Read mode (see (see Figure Every data transmission from ...
Page 8
NXP Semiconductors SCL slave address SDA START condition write to port data output from port P05 output voltage P05 pull-up output current P16 output voltage ...
Page 9
SCL P0x SDA DATA 00 START condition R/W acknowledge from slave read from port 0 data into port 0 DATA 00 ...
Page 10
SCL P0x SDA DATA 00 START condition R/W acknowledge from slave read from port 0 t h(D) data into port 0 ...
Page 11
NXP Semiconductors 8.4 Power-on reset When power is applied reset condition until V and the PCA8575 registers and I states. Thereafter V 8.5 Interrupt output (INT) The PCA8575 provides an open-drain interrupt (INT) which can be fed ...
Page 12
NXP Semiconductors 9. Characteristics of the I 2 The I C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be ...
Page 13
NXP Semiconductors SDA SCL MASTER TRANSMITTER/ RECEIVER Fig 17. System configuration 9.3 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed ...
Page 14
NXP Semiconductors 10. Application design-in information 10.1 Bidirectional I/O expander applications In the 8-bit I/O expander application shown in to P07 are outputs. When used in this configuration, during a write, the input (P00 and P01) must be written as ...
Page 15
NXP Semiconductors 10.3 Differences between the PCA8575 and the PCF8575 The PCA8575 is a drop in replacement for the PCF8575 and can used without electrical or software modifications, but there is a difference in interrupt output release timing during the ...
Page 16
NXP Semiconductors 12. Static characteristics Table 5. Static characteristics Symbol Parameter Supplies V supply voltage DD I supply current DD I standby current stb V power-on ...
Page 17
NXP Semiconductors 13. Dynamic characteristics Table 6. Dynamic characteristics Symbol Parameter f SCL clock frequency SCL t bus free time between a STOP and START BUF ...
Page 18
NXP Semiconductors START protocol condition (S) t SU;STA SCL t BUF SDA t HD;STA Rise and fall times refer Fig 21. I C-bus timing diagram PCA8575_1 Objective data sheet Remote 16-bit I/O expander for I bit 7 ...
Page 19
NXP Semiconductors 14. Package outline SO24: plastic small outline package; 24 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT ...
Page 20
NXP Semiconductors SSOP24: plastic shrink small outline package; 24 leads; body width 5 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.21 1. ...
Page 21
NXP Semiconductors SSOP24: plastic shrink small outline package; 24 leads; body width 3.9 mm; lead pitch 0.635 DIMENSIONS (millimetre dimensions are derived from the original inch dimensions) A UNIT ...
Page 22
NXP Semiconductors TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.15 0.95 mm ...
Page 23
NXP Semiconductors DHVQFN24: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 24 terminals; body 3.5 x 5.5 x 0.85 mm terminal 1 index area terminal 1 index area ...
Page 24
NXP Semiconductors HVQFN24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 0.85 mm terminal 1 index area terminal 1 24 index area DIMENSIONS (mm are ...
Page 25
NXP Semiconductors 15. Handling information Inputs and outputs are protected against electrostatic discharge in normal handling. However completely safe you must take normal precautions appropriate to handling integrated circuits. 16. Soldering This text provides a very brief insight ...
Page 26
NXP Semiconductors • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities ...
Page 27
NXP Semiconductors Fig 28. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description” . 17. Abbreviations Table 9. Acronym CDM CMOS ESD GPIO HBM I/O 2 ...
Page 28
NXP Semiconductors 18. Revision history Table 10. Revision history Document ID Release date PCA8575_1 20061130 PCA8575_1 Objective data sheet Remote 16-bit I/O expander for I Data sheet status Change notice Objective data sheet - Rev. 01 — 30 November 2006 ...
Page 29
NXP Semiconductors 19. Legal information 19.1 Data sheet status [1][2] Document status Product status Objective [short] data sheet Development Preliminary [short] data sheet Qualification Product [short] data sheet Production [1] Please consult the most recently issued document before initiating or ...
Page 30
NXP Semiconductors 21. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . ...