LV8138V SANYO [Sanyo Semicon Device], LV8138V Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
LV8138V
Manufacturer Part Number
LV8138V
Description
Bi-CMOS IC For Brushless Motor Drive Sine wave PWM Drive, Pre driver IC
Manufacturer
SANYO [Sanyo Semicon Device]
Datasheet
1.LV8138V.pdf
(19 pages)
6. VREG Stabilization
7. Forward/Reverse Switching (F/R pin)
8. TH Pin
9. FAULT Pin
10. PWM Frequency Setting
A capacitor of at least 0.1μF must be used to stabilize the VREG voltage, which is the control circuit power supply. The
ground lead of that capacitor must be located as close as possible to the control system ground (SGND) of the IC.
Switching between forward rotation and reverse rotation must not be undertaken while the motor is running.
The TH pin must normally be pulled up to the 5V regulator for use. When it has been set to low, the outputs are low.
The FAULT pin must normally be pulled up to the 5V regulator for use. When it has been set to low, the outputs are low.
In addition, the FG output does OFF, too
Components with good temperature characteristics must be used.
An oscillation frequency of about 17kHz is obtained when a 2200pF capacitor and 15kΩ resistor are used. If the PWM
frequency is too low, switching noise will be heard from the motor; conversely, if it is too high, the output power loss
will increase. For this reason, a frequency between 15kHz and 30kHz or so is desirable. The capacitor ground must be
connected as close as possible to the control system ground (SGND pin) of the IC to minimize the effects of the outputs.
fCPWM ≈ 1/ (1.78CR)
This catalog provides information as of February, 2012. Specifications and information herein are subject
to change without notice.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
LV8138V
PS No.A2013-19/19