M29W320ET STMICROELECTRONICS [STMicroelectronics], M29W320ET Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
M29W320ET
Manufacturer Part Number
M29W320ET
Description
32 Mbit (4Mb x8 or 2Mb x16, Boot Block) 3V Supply Flash Memory
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.M29W320ET.pdf
(46 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M29W320ET-70N6
Manufacturer:
ST
Quantity:
9 025
Company:
Part Number:
M29W320ET-70N6
Manufacturer:
RENESA
Quantity:
3 236
Part Number:
M29W320ET-70N6
Manufacturer:
ST
Quantity:
20 000
Part Number:
M29W320ET-70N6-H
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M29W320ET-70N6E
Manufacturer:
ST
Quantity:
9 030
Company:
Part Number:
M29W320ET-70N6E
Manufacturer:
CY
Quantity:
5 233
Part Number:
M29W320ET-70N6L
Manufacturer:
ST
Quantity:
20 000
SUMMARY DESCRIPTION
The M29W320E is a 32 Mbit (4Mb x8 or 2Mb x16)
non-volatile memory that can be read, erased and
reprogrammed. These operations can be per-
formed using a single low voltage (2.7 to 3.6V)
supply. On power-up the memory defaults to its
Read mode.
The device features an asymmetrical block archi-
tecture. The M29W320E has an array of 8 param-
eter and 63 main blocks. M29W320ET locates the
Parameter Blocks at the top of the memory ad-
dress space while the M29W320EB locates the
Parameter Blocks starting from the bottom.
M29W320E has an extra 32 KWord (x16 mode) or
64 KByte (x8 mode) block, the Extended Block,
that can be accessed using a dedicated com-
mand. The Extended Block can be protected and
so is useful for storing security information. How-
ever the protection is irreversible, once protected
the protection cannot be undone.
Each block can be erased independently so it is
possible to preserve valid data while old data is
Figure 2. Logic Diagram
A0-A20
RP
W
G
E
21
M29W320ET
M29W320EB
V CC
V SS
V PP /WP
15
DQ0-DQ14
DQ15A–1
BYTE
RB
AI09346
erased. The blocks can be protected to prevent
accidental Program or Erase commands from
modifying the memory. Program and Erase com-
mands are written to the Command Interface of
the memory. An on-chip Program/Erase Controller
simplifies the process of programming or erasing
the memory by taking care of all of the special op-
erations that are required to update the memory
contents. The end of a program or erase operation
can be detected and any error conditions identi-
fied. The command set required to control the
memory is consistent with JEDEC standards.
Chip Enable, Output Enable and Write Enable sig-
nals control the bus operation of the memory.
They allow simple connection to most micropro-
cessors, often without additional logic.
The memory is offered in TSOP48 (12x20mm), and
TFBGA48 (6x8mm, 0.8mm pitch) packages. The
memory is supplied with all the bits erased (set to
’1’).
Table 1. Signal Names
A0-A20
DQ0-DQ7
DQ8-DQ14
DQ15A–1
E
G
W
RP
RB
BYTE
V
V
V
NC
CC
SS
PP
/WP
Address Inputs
Data Inputs/Outputs
Data Inputs/Outputs
Data Input/Output or Address Input
Chip Enable
Output Enable
Write Enable
Reset/Block Temporary Unprotect
Ready/Busy Output
Byte/Word Organization Select
Supply Voltage
V
Ground
Not Connected Internally
PP
M29W320ET, M29W320EB
/Write Protect
5/46