M29DW323DB ST Microelectronics, M29DW323DB Datasheet - Page 17
![no-image](/images/no-image-200.jpg)
M29DW323DB
Manufacturer Part Number
M29DW323DB
Description
32 Mbit 4Mb x8 or 2Mb x16 / Dual Bank 8:24 / Boot Block 3V Supply Flash Memory
Manufacturer
ST Microelectronics
Datasheet
1.M29DW323DB.pdf
(49 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M29DW323DB-70N6
Manufacturer:
TI
Quantity:
54
Company:
Part Number:
M29DW323DB-90N6
Manufacturer:
INT
Quantity:
3 900
Part Number:
M29DW323DB5AN6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M29DW323DB70N6
Manufacturer:
SANYO
Quantity:
792
Part Number:
M29DW323DB70N6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M29DW323DB70N6E
Manufacturer:
VISHAY
Quantity:
6 700
blocks are protected the Chip Erase operation ap-
pears to start but will terminate within about 100µs,
leaving the data unchanged. No error condition is
given when protected blocks are ignored.
During the erase operation the memory will ignore
all commands, including the Erase Suspend com-
mand. It is not possible to issue any command to
abort the operation. Typical chip erase times are
given in Table 7. All Bus Read operations during
the Chip Erase operation will output the Status
Register on the Data Inputs/Outputs. See the sec-
tion on the Status Register for more details.
After the Chip Erase operation has completed the
memory will return to the Read Mode, unless an
error has occurred. When an error occurs the
memory will continue to output the Status Regis-
ter. A Read/Reset command must be issued to re-
set the error condition and return to Read Mode.
The Chip Erase Command sets all of the bits in un-
protected blocks of the memory to ’1’. All previous
data is lost.
Block Erase Command
The Block Erase command can be used to erase
a list of one or more blocks in a Bank. It sets all of
the bits in the unprotected selected blocks to ’1’.
All previous data in the selected blocks is lost.
Six Bus Write operations are required to select the
first block in the list. Each additional block in the
list can be selected by repeating the sixth Bus
Write operation using the address of the additional
block. All blocks must belong to the same Bank; if
a block belonging to the other Bank is given it will
not be erased. The Block Erase operation starts
the Program/Erase Controller after a time-out pe-
riod of 50µs after the last Bus Write operation.
Once the Program/Erase Controller starts it is not
possible to select any more blocks. Each addition-
al block must therefore be selected within 50µs of
the last block. The 50µs timer restarts when an ad-
ditional block is selected. After the sixth Bus Write
operation a Bus Read operation within the same
Bank will output the Status Register. See the Sta-
tus Register section for details on how to identify if
the Program/Erase Controller has started the
Block Erase operation.
If any selected blocks are protected then these are
ignored and all the other selected blocks are
erased. If all of the selected blocks are protected
the Block Erase operation appears to start but will
terminate within about 100µs, leaving the data un-
changed. No error condition is given when protect-
ed blocks are ignored.
During the Block Erase operation the memory will
ignore all commands except the Erase Suspend
command and the Read/Reset command which is
only accepted during the 50µs time-out period.
Typical block erase times are given in Table 7.
After the Erase operation has started all Bus Read
operations to the Bank being erased will output the
Status Register on the Data Inputs/Outputs. See
the section on the Status Register for more details.
After the Block Erase operation has completed the
memory will return to the Read Mode, unless an
error has occurred. When an error occurs Bus
Read operations to the Bank where the command
was issued will continue to output the Status Reg-
ister. A Read/Reset command must be issued to
reset the error condition and return to Read mode.
Erase Suspend Command
The Erase Suspend Command may be used to
temporarily suspend a Block Erase operation and
return the memory to Read mode. The command
requires one Bus Write operation.
The Program/Erase Controller will suspend within
the Erase Suspend Latency time of the Erase Sus-
pend Command being issued. Once the Program/
Erase Controller has stopped the memory will be
set to Read mode and the Erase will be suspend-
ed. If the Erase Suspend command is issued dur-
ing the period when the memory is waiting for an
additional block (before the Program/Erase Con-
troller starts) then the Erase is suspended immedi-
ately and will start immediately when the Erase
Resume Command is issued. It is not possible to
select any further blocks to erase after the Erase
Resume.
During Erase Suspend it is possible to Read and
Program cells in blocks that are not being erased;
both Read and Program operations behave as
normal on these blocks. If any attempt is made to
program in a protected block or in the suspended
block then the Program command is ignored and
the data remains unchanged. The Status Register
is not read and no error condition is given. Read-
ing from blocks that are being erased will output
the Status Register.
It is also possible to issue the Auto Select, Read
CFI Query and Unlock Bypass commands during
an Erase Suspend. The Read/Reset command
must be issued to return the device to Read Array
mode before the Resume command will be ac-
cepted.
During Erase Suspend a Bus Read operation to
the Extended Block will output the Extended Block
data.
Erase Resume Command
The Erase Resume command must be used to re-
start the Program/Erase Controller after an Erase
Suspend. The device must be in Read Array mode
before the Resume command will be accepted. An
erase can be suspended and resumed more than
once.
M29DW323DT, M29DW323DB
17/49