C1206H124C1GACTU KEMET [Kemet Corporation], C1206H124C1GACTU Datasheet - Page 2

• Manufacturer Part Number: C1206H124C1GACTU
• Manufacturer: KEMET [Kemet Corporation]

Ordering Information
Electrical Parameters/Characteristics
*Contact KEMET for availability and ordering details if you require additional reeling or packaging options.
Additional termination options may be available, contact KEMET for details.
Qualifi cation/Certifi cation
RoHS-PRC (6/6) - 100% matte Sn termination
Ceramic
Capacitance and Dissipation Factor (DF) measured under the following conditions:
1kHz and 1 Vrms if capacitance >1000pF
1MHz and 1 Vrms if capacitance ≤1000pF
High Temperature Life
Load Humidity
Low Voltage Humidity
Temperature Cycling
Thermal Shock
Moisture Resistance
Resistance to Solvents
Mechanical Shock and Vibration
Restistance to Soldering Heat
Terminal Strength
Board Flex
Aging Rate (Max % Cap Loss/Decade Hour): 0%
C
Insulation Resistance (IR) Limit @ 200°C:
Temperature Coeffi cient of Capacitance : ±30PPM/ºC (up to 200ºC)
Insulation Resistance (IR) Limit @ 25°C:
Case Size
1210
(L”x W”)
0603
0805
1206
1210
1812
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 [phone] • www.kemet.com
Dielectric Withstanding Voltage: 250%
Dissipation Factor (DF) @ 25ºC: .001 (0.10%) Max
Operating Temperature Range: -55°C to +200°C
H = High Temp (200ºC)
Specifi cation/
Series
H
PHYSICAL, MECHANICAL & PROCESS TESTS per MIL-STD 202/JIS-C-6429
RELIABILITY/ ENVIRONMENTAL TESTS per MIL-STD-202/JESD22
*Use 9 for 1.0 - 9.9pF
*Use 8 for 0.5 - .99pF
Capacitance Code
ex. 2.2pF = 229
ex. 0.5pF = 508
2 Sig. Digits +
Number of
124
Zeros*
(pF)
200ºC, Rated Voltage, 2000 Hours.
85ºC /85%RH, Rated Voltage, 1000 Hours.
85ºC /85%RH, 1.5V, 1000 Hours.
-55ºC to +200ºC, 50 Cycles.
-55ºC to +150ºC, 20s transfer, 15 min dwell, 300 Cycles.
Cycled Temp / RH. 0V, 10 cycles @ 24 Hrs each.
Include Aqueous wash chemical - OKEM Clean or equivalent.
Method 213: Figure 1, Condition F Method 204: 5 gs for 20 min,12 cycles.
Condition B, no pre-heat of samples, Single Wave Solder.
Force of 1.8 kg for 60 seconds.
3mm minimum.
Product Qualifi cation Test Plan
1000 megohm microfarads or 100GΩ
10 megohm microfarads or 1GΩ
Capacitance
C = ±0.25pF
Tolerance
D = ±0.5pF
M = ±20%
K = ±10%
G = ±2%
F = ±1%
J = ±5%
J
1 = 100V
2 = 200V
Voltage Dielectric
8 = 10V
4 = 16V
3 = 25V
6 = 35V
5 = 50V
5
G = C0G
G
Failure Rate/
Design
A = N/A
A
End Metallization
C = 100% Matte Sn
L = SnPb (5% min) TU = 7” Reel Unmarked
(Plated)
C
TM = 7” Reel Marked
Packaging/Grade
Blank = Bulk
F4002 01/10
(C-Spec)*
TU