MP7612AP EXAR [Exar Corporation], MP7612AP Datasheet - Page 6

• Manufacturer Part Number: MP7612AP
• Description: Octal 12-Bit DAC Array D/A Converter with Output Amplifier and Serial Data/Address uP Control Logic
• Manufacturer: EXAR [Exar Corporation]

ABSOLUTE MAXIMUM RATINGS (TA = +25 C unless otherwise noted)
V
V
DV
V
AGND to DGND
(Functionality guaranteed for
Digital Input & Output Voltage to DGND –0.5 to DV
+0.5V
NOTES:
1
2
APPLICATION NOTES
Refer to Section 8 in the 1995 Data Acquisition products Databook for Applications Information
NOTE: When using these DACs to drive remote devices, the accuracy of the output can be improved by utilizing a remote analog
ground connection. The difference between the DGND and AGND should be limited to
is any chance that the AGND to DGND can be greater than
and AGND to clamp the voltage and prevent damage to the DAC. Using a buffer between the remote ground location and AGND may
help reduce noise induced from long lead or trace lengths.
MP7612
ELECTRICAL CHARACTERISTICS (CONT’D)
NOTES:
1
2
3
4
5
6
CC
EE
REF
DD
to AGND
Rev. 3.00
to AGND
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a
stress rating only and functional operation at or above this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
Any input pin which can see a value outside the absolute maximum ratings should be protected by Schottky diode clamps
(HP5082-2835) from input pin to the supplies. All inputs have protection diodes which will protect the device from short
transients outside the supplies of less than 100mA for less than 100 s.
to DGND
Guaranteed; not tested.
Specified values guarantee functionality.
Digital inputs should not go below digital GND or exceed DV
See Figures 2 and 3 . All digital input signals are specified with t
For power supply values <
Digital feedthrough and channel-to-channel crosstalk are heavily dependent on the board layout and environment.
to DGND
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 V
0.5 V only)
REF
, the output swing is limited as specified in Analog Outputs.
Specifications are subject to change without notice
+16.5 V
–16.5 V
+6.5 V
+7.0 V
+1 V
DD
DD
1 V, we recommend two back-to-back diodes be used between DGND
R
= t
supply voltage.
6
F
= 10 ns 10% to 90% and timed from a 50% voltage level.
Analog Inputs & Outputs
V
dissipation of the package spec is not exceeded)
Operating Temperature Range
Maximum Junction Temperature
Storage Temperature
Lead Temperature (Soldering, 10 sec)
Package Power Dissipation Rating @ 75 C
Extended Industrial
CC
SOIC, PLCC
Derates above 75 C
, V
EE
, DV
DD
1, 2
, AGND, DGND (provided that power
. . . . . . . . . . . . . . . . . . . . . . . .
300 mV to assure normal operation. If there
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . .
. . .
Indefinite Shorts to
–40 C to +85 C
–65 C to 150 C
. . . . .
15mW/ C
1150mW
+300 C
150 C