ST72521 STMICROELECTRONICS [STMicroelectronics], ST72521 Datasheet - Page 26
ST72521
Manufacturer Part Number
ST72521
Description
8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, FIVE TIMERS, SPI, SCI, I2C, CAN INTERFACE
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.ST72521.pdf
(211 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST72521BTC
Manufacturer:
ST
Quantity:
11 000
- Current page: 26 of 211
- Download datasheet (3Mb)
ST72521
6.3 RESET SEQUENCE MANAGER (RSM)
6.3.1 Introduction
The reset sequence manager includes three RE-
SET sources as shown in
These sources act on the RESET pin and it is al-
ways kept low during the delay phase.
The RESET service routine vector is fixed at ad-
dresses FFFEh-FFFFh in the ST7 memory map.
The basic RESET sequence consists of 3 phases
as shown in
The 256 or 4096 CPU clock cycle delay allows the
oscillator to stabilise and ensures that recovery
has taken place from the Reset state. The shorter
or longer clock cycle delay should be selected by
option byte to correspond to the stabilization time
of the external oscillator used in the application
(see
Figure 12. Reset Block Diagram
26/211
External RESET source pulse
Internal LVD RESET (Low Voltage Detection)
Internal WATCHDOG RESET
Active Phase depending on the RESET source
256 or 4096 CPU clock cycle delay (selected by
option byte)
RESET vector fetch
RESET
Section 14.1 on page
Figure
11:
V
Figure
199).
DD
R
ON
12:
Filter
The RESET vector fetch phase duration is 2 clock
cycles.
Figure 11. RESET Sequence Phases
6.3.2 Asynchronous External RESET pin
The RESET pin is both an input and an open-drain
output with integrated R
This pull-up has no fixed value but varies in ac-
cordance with the input voltage. It can be pulled
low by external circuitry to reset the device. See
“CONTROL
page 186
A RESET signal originating from an external
source must have a duration of at least t
order to be recognized (see
tection is asynchronous and therefore the MCU
can enter reset state even in HALT mode.
GENERATOR
PULSE
Active Phase
for more details.
PIN
256 or 4096 CLOCK CYCLES
INTERNAL RESET
RESET
CHARACTERISTICS”
ON
weak pull-up resistor.
WATCHDOG RESET
LVD RESET
Figure
INTERNAL
RESET
13). This de-
VECTOR
h(RSTL)in
FETCH
on
in
Related parts for ST72521
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
THYRISTORS
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
0.25A SCRs
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
0.8A SCRs
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Smartcard MCU With 4 additional I/0
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
SERIAL 2K (256 x 8) EEPROM
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Search -----> STP10NB50FP
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Search ---> STP12NB30
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Search -----> STP13NK50Z
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(MSS40 / MSS50) BACK TO BACK SCR MODULE
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Dmos Programmable High Speed Unipolar Stepper Motor Driver
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
LOW Votage Telephone Speech Circuit
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Technical Article
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Thyristormodule
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
SCR
Manufacturer:
ST Microelectronics
Datasheet: