SS8014-18GTR SSC [Silicon Standard Corp.], SS8014-18GTR Datasheet
SS8014-18GTR
Available stocks
Related parts for SS8014-18GTR
SS8014-18GTR Summary of contents
Page 1
... SS8014 to prevent thermal overload. These power saving features make the SS8014 ideal for use in such battery-powered applications as notebook computers, cellular phones, and PDA’s. ORDERING INFORMATION Part Number SS8014-15GTR SS8014-18GTR SS8014-25GTR SS8014-27GTR SS8014-28GTR SS8014-29GTR SS8014-30GTR SS8014-33GTR Typical Operating Circuit ...
Page 2
... J SYMBOL CONDITIONS V IN Variation from specified =1mA,V OUT For SS8014-18, I =1mA OUT OUT For SS8014-15, I =1mA OUT I LIM I = 0mA LOAD I V =3. 50mA Q IN LOAD I ...
Page 3
... Note 4: The dropout voltage is defined as (V For the performance of e ach SS8014-xx version, see “Typical Performance Characteristics”. Note 5: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 1mA to 300mA. Changes in output due to heating effects are covered by the thermal regulation specification ...
Page 4
... SHDN Input Bias Current vs. Temperature 0.20 SS8014- SHDN 0.10 0.00 -0.10 -0. -40 -30 -20 - (°C) Output Voltage vs. Temperature 3.36 SS8014-33 3.34 I LOAD 3.32 3.30 3.28 3.26 3. -40 -30 -20 - (°C) J =0mA ...
Page 5
... Output Noise vs. Load Current =1µ 0.1 1 www.SiliconStandard.com SS8014-xxG Load Transient SS8014-29 V =5V +2V(p-p) IN =100 =10nF BYP 0 0 100 Frequency(KHZ) SS8014-18 V =2.8V IN =25 ° =1µF OUT 10 100 1000 Load Current (mA ...
Page 6
... Bypass Capactor (nF) 1/12/2005 Rev.2.10 (continued) Power Off Response Waveform Shutdown Delay Waveform Turn-Off Time vs. Bypass Capacitance 1000 100 100 0.1 www.SiliconStandard.com SS8014-xxG Propagation Delay Time Fall Time SS8014-33 I =150mA LOAD C =C =1µF IN OUT V =4.3V power already IN V =4. SHDN 1 10 100 ...
Page 7
... OUT Regulator Output. Sources up to 150mA. Bypass with a 1µF, < 0.2 Detailed Description The block diagram of the SS8014-xx is shown in Figure 1. It consists of an error amplifier, 1.25V bandgap reference, PMOS output transistor, internal feedback voltage divider, shutdown logic, over current protection circuit, and over temperature protection circuit. The internal feedback voltage divider’ ...
Page 8
... The typical over current limit of the SS8014 is set to 350mA. Note that the input bypass capacitor of 1µF must be used in this case to filter out the input voltage spike caused by the surge current due to the inductive effect of the package pin and the printed circuit board’ ...
Page 9
... Layout Guide An input capacitance of ~1µF is required between the SS8014 input pin and ground (the amount of the ca- pacitance may be increased without limit), This ca- pacitor must be located a distance of not more than 1cm from the input and return to a clean analog ground. The input capacitor filters out the input voltage spike caused by the surge current due to the inductive effect of the package pin and the printed circuit board’ ...
Page 10
... Silicon Standard Corporation or any third parties. 1/12/2005 Rev.2. DIMENSIONS IN MILLIMETERS MIN NOM 1.00 1.10 0.00 ----- 0.70 0.80 0.35 0.40 0.10 0.15 2.70 2.90 1.40 1.60 ----- 1.90(TYP) ----- 0.95 2.60 2.80 0.37 ------ 1º 5º www.SiliconStandard.com SS8014-xxG Tape/package orientation Feed Direction SOT23-5 package orientation MAX 1.30 0.10 0.90 0.50 0.25 3.10 1.80 ----- ----- 3.00 ----- 9º ...