saa3008 NXP Semiconductors, saa3008 Datasheet
saa3008
Available stocks
Related parts for saa3008
saa3008 Summary of contents
Page 1
... DATA SHEET SAA3008 Infrared remote control transmitter (RECS 80 low voltage) Preliminary specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS December 1988 ...
Page 2
... The subsystem address may be selected by press-button, slider switches or be hard-wired. Commands are transmitted in patterns which are pulse distance coded. Modulated pulse transmissions allow a narrow-band receiver to be used for improved noise rejection. The modulation frequency of the SAA3008 is 38 kHz which the oscillator frequency of 455 kHz (typical) ...
Page 3
... Philips Semiconductors Infrared remote control transmitter (RECS 80 low voltage) Fig.2 Pinning diagram. December 1988 Fig.1 SAA3008 application example. PINNING 1 REMO 2 SEN6N 3 SEN5N 4 SEN4N 5 SEN3N 6 SEN2N 7 SEN1N 8 SEN0N 9 ADRM OSCI 12 OSCO 13 DRV0N 14 DRV1N 15 DRV2N 16 DRV3N 17 DRV4N 18 DRV5N 19 DRV6N Preliminary specification ...
Page 4
... The toggle bit T0 acts as an indication for the decoder whether the next instruction should be considered as a new command or not. The codes for the subsystem address and the selected key are given in Table 3. 4 Preliminary specification SAA3008 ’ between the b (Table 3) which o osc ...
Page 5
... When operating at a supply voltage of below 270 kHz resistor should be connected in parallel with the resonator. December 1988 Fig.3 Data format of remote control signal (REMO). 5 Preliminary specification SAA3008 ...
Page 6
... Preliminary specification SAA3008 ...
Page 7
... Preliminary specification SAA3008 ...
Page 8
... Preliminary specification SAA3008 ...
Page 9
... The toggle bit T0 is incremented if the key is released for a minimum time t (Fig.5 multiple keystroke REL sequence the toggle bit remains unchanged. 9 Preliminary specification SAA3008 DURATION 455 kHz; OSC t = 2.2 s OSC 26 ...
Page 10
Fig.5 Single keystroke sequence debounce time = start time = 5T to 10T ; minimum release time = T ; REL ...
Page 11
... 300 tot P 200 tot 200 amb T 20 125 stg MIN. TYP. 2.0 6.5 0.25 0 350 500 0 100 100 600 SAA3008 UNIT V 0 MAX. UNIT kHz ...
Page 12
... 6 100 6 100 6 Preliminary specification MIN. TYP. MAX. 0.3 0.6 10 0 100 100 600 10 100 100 600 0.8 5.0 0 0.4 0.4 3.0 7.0 V 0.8 DD 0.7 SAA3008 UNIT ...
Page 13
... Philips Semiconductors Infrared remote control transmitter (RECS 80 low voltage) December 1988 Fig.7 REMO output stage. 13 Preliminary specification SAA3008 ...
Page 14
... 1.73 0.53 0.36 26.92 6.40 1.30 0.38 0.23 26.54 6.22 0.068 0.021 0.014 1.060 0.25 0.051 0.015 0.009 1.045 0.24 REFERENCES JEDEC EIAJ SC603 14 Preliminary specification 3.60 8.25 10.0 2.54 7.62 3.05 7.80 8.3 0.14 0.32 0.39 0.10 0.30 0.12 0.31 0.33 EUROPEAN PROJECTION SAA3008 SOT146 ( max. 0.254 2.0 0.01 0.078 ISSUE DATE 92-11-17 95-05-24 ...
Page 15
... REFERENCES JEDEC EIAJ MS-013AC 15 Preliminary specification detail 1.1 1.1 1.4 0.25 0.25 0.4 1.0 0.043 0.043 0.055 0.01 0.01 0.016 0.039 EUROPEAN PROJECTION SAA3008 SOT163 ( 0.9 0.1 0 0.035 0.004 0.016 ISSUE DATE 95-01-24 97-05-22 ...
Page 16
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 16 Preliminary specification SAA3008 ...
Page 17
... Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. December 1988 17 Preliminary specification SAA3008 ...