smc032af STMicroelectronics, smc032af Datasheet - Page 18
smc032af
Manufacturer Part Number
smc032af
Description
32 Mbyte, 64 Mbyte, 128 Mbyte, 256 Mbyte And 512 Mbyte 3.3 V / 5 V Supply Compactflash Card
Manufacturer
STMicroelectronics
Datasheet
1.SMC032AF.pdf
(82 pages)
- Current page: 18 of 82
- Download datasheet (702Kb)
Electrical interface
Table 9.
18/82
READY
(PC card memory mode)
–IREQ
(PC card I/O mode)
INTRQ
(True IDE mode)
–REG
(PC card memory mode)
–REG
(PC card I/O mode)
Reserved
(True IDE mode)
RESET
(PC card memory mode)
RESET
(PC card I/O mode)
–RESET
(True IDE mode)
V
(PC card memory mode)
V
(PC card I/O mode)
V
(True IDE mode)
–VS1, –VS2
(PC card memory mode)
–VS1, –VS2
–VS1, –VS2
–WAIT
(PC card memory mode)
–WAIT
(PC card I/O mode)
IORDY
(True IDE mode)
(PC card I/O mode)
(True IDE mode)
CC
CC
CC
Signal name
Signal description (continued)
O
I
I
O
O
Direction
37
44
41
13,38
33,40
42
Pin
Indicates whether the card is busy (Low), or ready to
accept a new data transfer operation (High). The Host
socket must provide a pull-up resistor. At power-up and
reset, the READY signal is held Low until the commands
are completed. No access should be made during this
time. The READY signal is held High whenever the card
has been powered up with RESET continuously
disconnected or asserted.
Interrupt request. It is strobed Low to generate a pulse
mode interrupt or held Low for a level mode interrupt.
Active High Interrupt request to the host.
Used to distinguish between common memory and
register (attribute) memory accesses. High for common
memory, Low for attribute memory.
Must be Low during I/O cycles when the I/O address is on
the bus.
Not used, should be connected to V
Resets the card (active High). The card is reset at power-
up only if this pin is left High or unconnected.
Same as PC card memory mode.
Hardware Reset from the host (active Low).
+5 V, +3.3 V power.
Same for all modes.
Same for all modes.
Voltage sense signals.–VS1 is grounded so that the CIS
can be read at 3.3 volts and –VS2 is reserved by PCMCIA
for a secondary voltage.
Same for all modes.
Same for all modes.
ST CF does not assert the WAIT (IORDY) signal.
Description
CC
by the host.
SMCxxxAF
Related parts for smc032af
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Smc Series-160808
Manufacturer:
3L Electronic Group Holdings Limited
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: