mtsf3n03hdr2 Freescale Semiconductor, Inc, mtsf3n03hdr2 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mtsf3n03hdr2
Manufacturer Part Number
mtsf3n03hdr2
Description
Tmos Single N-channel Field Effect Transistor
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MTSF3N03HDR2.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MTSF3N03HDR2
Manufacturer:
PHILIPS
Quantity:
450
Part Number:
MTSF3N03HDR2
Manufacturer:
ON/安森美
Quantity:
20 000
are very important in systems using it as a freewheeling or
commutating diode. Of particular interest are the reverse re-
covery characteristics which play a major role in determining
switching losses, radiated noise, EMI and RFI.
the body diode itself. The body diode is a minority carrier de-
vice, therefore it has a finite reverse recovery time, t rr , due to
the storage of minority carrier charge, Q RR , as shown in the
typical reverse recovery wave form of Figure 13. It is this
stored charge that, when cleared from the diode, passes
through a potential and defines an energy loss. Obviously,
repeatedly forcing the diode through reverse recovery further
increases switching losses. Therefore, one would like a
diode with short t rr and low Q RR specifications to minimize
these losses.
amount of radiated noise, voltage spikes, and current ring-
ing. The mechanisms at work are finite irremovable circuit
parasitic inductances and capacitances acted upon by high
MTSF3N03HD
6
The switching characteristics of a MOSFET body diode
System switching losses are largely due to the nature of
The abruptness of diode reverse recovery effects the
12
10
8
6
4
2
0
0
Drain–To–Source Voltage versus Total Charge
Q1
3
Q3
Q2
Figure 10. Gate–To–Source and
V DS
Q g , TOTAL GATE CHARGE (nC)
6
9
QT
V GS
DRAIN–TO–SOURCE DIODE CHARACTERISTICS
12
4
3
2
1
0
Figure 12. Diode Forward Voltage versus Current
0.5
15
V GS = 0 V
T J = 25 C
V SD , SOURCE–TO–DRAIN VOLTAGE (VOLTS)
I D = 3.7 A
T J = 25 C
18
0.6
21
30
25
20
10
15
5
0
0.7
di/dts. The diode’s negative di/dt during t a is directly con-
trolled by the device clearing the stored charge. However,
the positive di/dt during t b is an uncontrollable diode charac-
teristic and is usually the culprit that induces current ringing.
Therefore, when comparing diodes, the ratio of t b /t a serves
as a good indicator of recovery abruptness and thus gives a
comparative estimate of probable noise generated. A ratio of
1 is considered ideal and values less than 0.5 are considered
snappy.
MOSFETs, high cell density MOSFET diodes are faster
(shorter t rr ), have less stored charge and a softer reverse re-
covery characteristic. The softness advantage of the high
cell density diode means they can be forced through reverse
recovery at a higher di/dt than a standard cell MOSFET
diode without increasing the current ringing or the noise gen-
erated. In addition, power dissipation incurred from switching
the diode will be less due to the shorter recovery time and
lower switching losses.
1000
Compared to Motorola standard cell density low voltage
Motorola TMOS Power MOSFET Transistor Device Data
100
10
1
1
V DD = 15 V
I D = 3.7 A
V GS = 10 V
T J = 25 C
0.8
Figure 11. Resistive Switching Time
Variation versus Gate Resistance
t d(on)
t d(off)
R G , GATE RESISTANCE (OHMS)
t f
t r
0.9
10
100