pcd3310 NXP Semiconductors, pcd3310 Datasheet
pcd3310
Available stocks
Related parts for pcd3310
pcd3310 Summary of contents
Page 1
... DATA SHEET PCD3310; PCD3310A Pulse and DTMF diallers with redial Product specification Supersedes data of 1996 May 06 File under Integrated Circuits, IC03 INTEGRATED CIRCUITS 1996 Nov 21 ...
Page 2
... Redialling 8.3 Notepad 9 HANDLING 10 LIMITING VALUES 11 CHARACTERISTICS 12 TIMING CHARACTERISTICS 13 APPLICATION INFORMATION 14 PACKAGE OUTLINES 15 SOLDERING 15.1 Introduction 15.2 DIP 15.2.1 Soldering by dipping or by wave 15.2.2 Repairing soldered joints 15.3 SO 15.3.1 Reflow soldering 15.3.2 Wave soldering 15.3.3 Repairing soldered joints 16 DEFINITIONS 17 LIFE SUPPORT APPLICATIONS 1996 Nov Product specification PCD3310; PCD3310A ...
Page 3
... Keyboard entries fully debounced Flash (register recall) output. 2 GENERAL DESCRIPTION The PCD3310 and PCD3310A are single-chip silicon gate CMOS integrated circuits. They are dual-standard diallers for pulse or dual tone multi-frequency (DTMF) dialling, with on-chip oscillators suitable for use with 3.58 MHz crystals. ...
Page 4
... PCD3310T PCD3310AP PCD3310AT Notes 1. Pulse frequency 10 Hz, inter-digit pause (t 2. Note that the PCD3310P; 10T and the PCD3310AP; 10AT differ only in the break/make ratio in pulse dialling. The break/make times equate to mark-to-space ratios and respectively. 1996 Nov 21 PACKAGE DESCRIPTION ...
Page 5
... Philips Semiconductors Pulse and DTMF diallers with redial 5 BLOCK DIAGRAM handbook, full pagewidth 1996 Nov 21 PCD3310; PCD3310A 5 Product specification ...
Page 6
... O dialling pulse and flash output 22 O muting output muting output 1 (active LOW muting output 1 25 not connected 26 I chip enable input 27 P positive supply voltage 28 O oscillator output 6 Product specification PCD3310; PCD3310A DESCRIPTION ...
Page 7
... ROW 2 9 ROW 1 10 MGE489 Fig.2 Pin configuration (DIP20 package). 7 FUNCTIONAL DESCRIPTION References to ‘the device’ apply to both the PCD3310 and the PCD3310A. 7.1 Power supply (V and The positive supply of the device (V voltage requirements as indicated in Chapter 11. To avoid undefined states of the device at power-on, an internal reset circuit clears the control logic and counters ...
Page 8
... Valid function keys are P, also DD FL and R. In the mixed mode all key entries are valid and executed accordingly. 8 Product specification PCD3310; PCD3310A as shown in e COLUMNS ...
Page 9
... Table 3 shows the frequency tolerance of the output tones for DTMF signalling. R FLD FLO (a) (b) Fig.5 Flash pulse duration setting. 9 Product specification PCD3310; PCD3310A and LOW group frequencies are generated SS . The single tone frequency will FLRC MGE492 ...
Page 10
... It is also active HIGH during flash and flash hold-over time. 7.10 Mute output (M1) Inverted output of M1. In the PCD3310P it is only available as a bonding option of M1. 7.11 Muting output (M2) Active HIGH output during actual dialling; i.e. during break or make time in pulse dialling, or during tone ON/OFF in DTMF dialling ...
Page 11
... During notepad programming the numbers entered will not be transmitted nor is the mute active, only the confidence tone is generated addressed through pointers 3 TWAC or RAC 2 1 MAIN REGISTER ADDRESS COUNTER Fig.6 Program memory map. 11 Product specification PCD3310; PCD3310A TEMPORARY REGISTER TEMPORARY WRITE ADDRESS COUNTER (TWAC) MGE493 ...
Page 12
... ACCESS DIGIT(S) 0 wait for access tone key-in R external number 462 75 30 ON-HOOK Fig.7 Pulse or DTMF dialling mode. 12 Product specification PCD3310; PCD3310A conversation mode standby mode pulse or tone out DIAL internal number OFF-HOOK key-in internal number 5 digits 12345 ...
Page 13
... DTMF or manual TONE-output # ON-HOOK REDIAL OFF-HOOK key-in R 462 total pulse output (PD DTMF) 23 digits ON-HOOK MGE495 Fig.8 Pulse/DTMF and mixed mode dialling. 13 Product specification PCD3310; PCD3310A ...
Page 14
... Fig.9 Notepad, memory clear, flash; independent of dialling mode. 1996 Nov 21 NOTEPAD REDIAL OFF-HOOK key-in R 355 44 99 key-in 23 digits ON-HOOK OFF-HOOK no key-in R redialling 14 Product specification PCD3310; PCD3310A FLASH OFF-HOOK key-in ACCESS DIGIT(S) 0 wait for access tone key-in external number 462 75 30 key-in FL REDIAL (see PABX procedure) ...
Page 15
... ON resistance KON R keyboard OFF resistance KOFF 1996 Nov 21 PARAMETER = 25 to +70 C; unless otherwise specified. amb CONDITIONS oscillator ON tone ON one OFF oscillator OFF; note 1 15 Product specification PCD3310; PCD3310A MIN. MAX. UNIT 0 ...
Page 16
... note 4 amb and all other pins open-circuit PCD3310X TONE MGE501 Fig.10 Tone output test circuit. 16 Product specification PCD3310; PCD3310A MIN. TYP. MAX 158 192 205 mV 125 150 ...
Page 17
... When any key is activated a square wave (330 Hz) is generated and appears at the CF output to serve as an acoustic feed-back for the user. SYMBOL DTMF dialling transmission and pause times (manual dialling transmission and pause times (redialling Pulse dialling (PCD3310) f dialling pulse frequency dp t inter-digit pause id t break time b t make time m Pulse dialling (PCD3310A) ...
Page 18
... DIALLING MODE MODE (no effect Product specification PCD3310; PCD3310A STATIC CONVERSATION MODE STANDBY MODE MGE497 ). ...
Page 19
... M1 M2 PD/DTMF The dashed line signifies floating. Fig.14 .Timing diagram for mixed mode (PD/DTMF open-circuit). 1996 Nov pulse dialling DTMF dialling 19 Product specification PCD3310; PCD3310A telephone number MGE500 MGE502 ...
Page 20
... Philips Semiconductors Pulse and DTMF diallers with redial 13 APPLICATION INFORMATION ook, full pagewidth 1996 Nov 21 PCD3310; PCD3310A 20 Product specification ...
Page 21
... Nov scale (1) ( 0.53 0.36 26.92 6.40 2.54 0.38 0.23 26.54 6.22 0.021 0.014 1.060 0.25 0.10 0.015 0.009 1.045 0.24 REFERENCES JEDEC EIAJ SC603 21 Product specification PCD3310; PCD3310A 3.60 8.25 10.0 7.62 0.254 3.05 7.80 8.3 0.14 0.32 0.39 0.30 0.01 0.12 0.31 0.33 EUROPEAN ...
Page 22
... scale (1) ( 0.32 18.1 7.6 10.65 1.27 0.23 17.7 7.4 10.00 0.013 0.71 0.30 0.42 0.050 0.055 0.009 0.69 0.29 0.39 REFERENCES JEDEC EIAJ MS-013AE 22 Product specification PCD3310; PCD3310A detail 1.1 1.1 1.4 0.25 0.25 0.1 0.4 1.0 0.043 0.043 0.01 0.01 0.004 0.016 0.039 EUROPEAN ISSUE DATE ...
Page 23
... V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 23 Product specification PCD3310; PCD3310A ...
Page 24
... Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given advisory and does not form part of the specification. 1996 Nov 21 PCD3310; PCD3310A 24 Product specification ...
Page 25
... Philips Semiconductors Pulse and DTMF diallers with redial 1996 Nov 21 PCD3310; PCD3310A NOTES 25 Product specification ...
Page 26
... Philips Semiconductors Pulse and DTMF diallers with redial 1996 Nov 21 PCD3310; PCD3310A NOTES 26 Product specification ...
Page 27
... Philips Semiconductors Pulse and DTMF diallers with redial 1996 Nov 21 PCD3310; PCD3310A NOTES 27 Product specification ...
Page 28
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + ...