mt18hts25672rhz Micron Semiconductor Products, mt18hts25672rhz Datasheet
mt18hts25672rhz
Related parts for mt18hts25672rhz
mt18hts25672rhz Summary of contents
Page 1
... DDR2 SDRAM SORDIMM MT18HTS25672RHZ – 2GB Features • 200-pin, small-outline registered dual in-line memo- ry module (SORDIMM) • Fast data transfer rates: PC2-4200, PC2-5300, or PC2-6400 • 2GB (256 Meg x 72) • Supports ECC error detection and correction • 1.8V DD • 3.0–3.6V DDSPD • ...
Page 2
... The data sheet for the base device can be found on Micron’s Web site. Notes: 2. All part numbers end with a two-place code (not shown) that designates component and PCB revisions. Consult factory for current revision codes. Example: MT18HTS25672RHZ-80EG1. PDF: 09005aef83f287c1 hts18c256x72rhz.pdf - Rev. A 3/10 EN ...
Page 3
Pin Assignments Table 4: Pin Assignments 200-Pin SORDIMM Front Pin Symbol Pin Symbol Pin DQ18 101 REF 3 DQ0 53 DQ19 103 105 DQ1 57 DQ24 107 9 DQS0# 59 ...
Page 4
... Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 5: Pin Descriptions Symbol Type Ax Input BAx Input ...
Page 5
... SPD EEPROM power supply: 1.7–3.6V. Reference voltage: V /2. DD Ground. No connect: These pins are not connected on the module. No function: These pins are connected within the module, but provide no functionality. Not used: These pins are not used in specific module configurations/operations. Reserved for future use. 5 Pin Descriptions and V ...
Page 6
Functional Block Diagram Figure 2: Functional Block Diagram RS1# RS0# DQS0# DQS0 DM0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQS1# DQS1 DM1 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQS2# DQS2 DM2 DQ16 DQ17 DQ18 DQ19 DQ20 ...
Page 7
... DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data trans- fers at the I/O pins. DDR2 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals ...
Page 8
... Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other condi- tions outside those indicated in the device data sheet are not implied. Exposure to absolute maximum rating conditions for extended periods may adversely affect reliability. ...
Page 9
... Component specifications are available on Micron's Web site. Module speed grades cor- relate with component speed grades. Table 7: Module and Component Speed Grades DDR2 components may exceed the listed module speed grades; module may not be available in all listed speed grades Module Speed Grade -1GA ...
Page 10
IDD Specifications Table 8: DDR2 I Specifications and Conditions – 2GB DD Values shown for MT47H256M8THN DDR2 SDRAM only and are computed from values specified in the 2Gb TwinDie (256 Meg x 8) component data sheet Parameter Operating one bank ...
Page 11
Table 8: DDR2 I Specifications and Conditions – 2GB (Continued) DD Values shown for MT47H256M8THN DDR2 SDRAM only and are computed from values specified in the 2Gb TwinDie (256 Meg x 8) component data sheet Parameter Operating bank interleave read ...
Page 12
Register and PLL Specifications Table 9: Register Specifications SSTU32872 devices or equivalent Parameter Symbol DC high-level V Control, command, IH(DC) input voltage DC low-level V Control, command, IL(DC) input voltage AC high-level V Control, command, IH(AC) input voltage AC low-level ...
Page 13
Table 10: PLL Specifications CUA845 device or JEDEC82-21 equivalent Parameter Symbol DC high-level V IH input voltage DC low-level V IL input voltage Input voltage (limits Input differential-pair V IX cross voltage Input differential volt- V ID(DC) age ...
Page 14
... Temperature Sensor with Serial Presence-Detect EEPROM The temperature sensor continuously monitors the module’s temperature and can be read back at any time over the I Table 12: Temperature Sensor with Serial Presence-Detect EEPROM Operating Conditions Parameter/Condition Supply voltage Supply current 3.3V DD Input high voltage: Logic 1; SCL, SDA Input low voltage: Logic 0 ...
Page 15
The interrupt mode enables software to reset EVENT# after a critical temperature thresh- old has been detected. Threshold points are set in the configuration register by the user. This mode triggers the critical temperature limit and both the MIN and ...
Page 16
Figure 3: EVENT# Pin Functionality Critical Alarm window (MAX) Alarm window (MIN) EVENT# interrupt mode EVENT# comparator mode EVENT# critical temperature only mode Table 14: Temperature Sensor Registers Name Pointer register Capability register Configuration register Alarm temperature upper boundary register ...
Page 17
Table 15: Pointer Register Bits 0– Table 16: Pointer Register Bits 0–2 Descriptions Capability Register The capability register indicates the features and functionality supported by the temper- ature sensor. ...
Page 18
Table 18: Capability Register Bit Description (Continued) Bit Description 4:3 Temperature resolution 00: 0.5°C LSB 01: 0.25°C LSB 10: 0.125°C LSB 11: 0.0625°C LSB 15:5 0: Must be set to zero Configuration Register Table 19: Configuration Register (Address: 0x01) 15 ...
Page 19
Table 20: Configuration Register Bit Descriptions (Continued) Bit Description 6 Alarm window lock bit 0: Alarm trips are not locked and can be changed 1: Alarm trips are locked and cannot be changed 7 Critical trip lock bit 0: Critical ...
Page 20
Figure 4: Hysteresis Applied to Temperature Around Trip Points Below window bit Above window bit 1. T Notes Hyst is the value set in the hysteresis bits of the configuration register. Table 21: Hysteresis Applied to Alarm ...
Page 21
Temperature Trip Point Registers The upper and lower temperature boundary registers are used to set the maximum and minimum values of the alarm window. LSB for these registers is 0.25°C. All RFU bits in the register will always report zero. ...
Page 22
Table 25: Temperature Register (Address: 0x05 Above Above Below MSB critical alarm alarm trip window window Table 26: Temperature Register Bit Descriptions Bit Description 13 Below alarm window 0: Temperature is equal to or above the lower ...
Page 23
... R 0.45 (0.018) Pin 1 TYP 2.504 (63.6) TYP Back view U9 U10 U11 4.2 (0.165) TYP 47.4 (1.87) TYP additional design dimensions. times occur. 23 Module Dimensions U6 30.15 (1.187) 29.85 (1.175) 20.0 (0.787) TYP 0.6 (0.024) Pin 199 TYP U12 10.0 (0.394) TYP Pin 2 11.4 (0.45) TYP 16.25 (0.64) TYP Micron Technology, Inc. reserves the right to change products or specifications without notice. ...