k4h510438f-llb3 Samsung Semiconductor, Inc., k4h510438f-llb3 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
k4h510438f-llb3
Manufacturer Part Number
k4h510438f-llb3
Description
512mb F-die Ddr Sdram Specification
Manufacturer
Samsung Semiconductor, Inc.
Datasheet
1.K4H510438F-LLB3.pdf
(24 pages)
Note :
1. V
2. V
3. V
4. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire temperature and voltage range,
The K4H510438F / K4H510838F / K4H511638F is 536,870,912 bits of double data rate synchronous DRAM organized as 4x 33,554,432
/ 4x 16,777,216 / 4x 8,388,608 words by 4/8/16bits, fabricated with SAMSUNG′s high performance CMOS technology. Synchronous fea-
tures with Data Strobe allow extremely high performance up to 400Mb/s per pin. I/O transactions are possible on both edges of DQS.
Range of operating frequencies, programmable burst length and programmable latencies allow the device to be useful for a variety of
high performance memory system applications.
Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
K4H510438F
K4H510838F
K4H511638F
9.0 General Description
10.0 Absolute Maximum Rating
11.0 DC Operating Conditions
Supply voltage(for device with a nominal V
Supply voltage(for device with a nominal V
I/O Supply voltage(for device with a nominal V
I/O Supply voltage(for device with a nominal V
I/O Reference voltage
I/O Termination voltage(system)
Input logic high voltage
Input logic low voltage
Input Voltage Level, CK and CK inputs
Input Differential Voltage, CK and CK inputs
V-I Matching: Pullup to Pulldown Current Ratio
Input leakage current
Output leakage current
Output High Current(Normal strengh driver) ;V
Output High Current(Normal strengh driver) ;V
Output High Current(Half strengh driver) ;V
Output High Current(Half strengh driver) ;V
32M x 4Bit x 4 Banks / 16M x 8Bit x 4 Banks / 8M x 16Bit x 4 Banks Double Data Rate SDRAM
exceed +/-2% of the dc value.
ations in the DC level of V
for device drain to source voltages from 0.25V to 1.0V. For a given output, it represents the maximum difference between pullup and pulldown drivers
due to process variation. The full variation in the ratio of the maximum to minimum pullup and pulldown current will not exceed 1.7 for device drain to
source voltages from 0.1 to 1.0.
REF
TT
ID
is not applied directly to the device. V
is the magnitude of the difference between the input level on CK and the input level on CK.
Functional operation should be restricted to recommend operation condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
Voltage on V
is expected to be equal to 0.5*V
Voltage on any pin relative to V
Storage temperature
DD
Short circuit current
& V
Parameter
REF
DDQ
supply relative to V
Parameter
DDQ
TT
of the transmitting device, and to track variations in the dc level of same. Peak-to peak noise on V
is a system supply for signal termination resistors, is expected to be set equal to V
DD
DD
SS
OUT
OUT
of 2.5V for DDR266/333)
of 2.6V for DDR400)
DD
DD
OUT
OUT
= V
= V
SS
of 2.5V for DDR266/333)
of 2.5V for DDR400)
= V
TT
= V
TT
Recommended operating conditions(Voltage referenced to V
+ 0.45V
TT
- 0.45V
TT
+ 0.84V
- 0.84V
10 of 24
V
V
Symbol
DD
IN
T
, V
I
, V
STG
OS
OUT
DDQ
Symbol
V
V
V
V
V
I
V
V
V
IH
IN
ID
IL
(Ratio)
V
V
V
I
I
I
I
I
DDQ
DDQ
REF
OH
OH
(DC)
OZ
OL
OL
(DC)
(DC)
(DC)
DD
DD
I
TT
I
-55 ~ +150
-0.5 ~ 3.6
-1.0 ~ 3.6
V
0.49*V
V
Value
REF
REF
50
-16.8
0.36
0.71
16.8
Min
-0.3
-0.3
Rev. 1.1 November 2008
2.3
2.5
2.3
2.5
-2
-5
-9
9
+0.15
-0.04
DDQ
0.51*V
V
V
V
V
V
REF
REF
DDQ
DDQ
DDQ
DDR SDRAM
Max
2.7
2.7
2.7
2.7
1.4
2
5
+0.04
-0.15
+0.3
+0.3
+0.6
DDQ
REF
SS
=0V, T
, and must track vari-
Unit
mA
°C
Unit
V
V
mA
mA
mA
mA
uA
uA
A
V
V
V
V
V
V
V
V
V
V
-
=0 to 70°C)
REF
may not
Note
1
2
3
4