adf7023-j Analog Devices, Inc., adf7023-j Datasheet - Page 96

• Manufacturer Part Number: adf7023-j
• Description: High Performance, Low Power, Ism Band Fsk/gfsk/msk/gmsk Transceiver Ic
• Manufacturer: Analog Devices, Inc.

ADF7023-J
Table 128. 0x3CB: VCO_BAND_OVRW_VAL
Bit
[7:0]
Table 129. 0x3CC: VCO_AMPL_OVRW_VAL
Bit
[7:0]
Table 130. 0x3CD: VCO_OVRW_EN
Bit
[7:6]
[5:2]
[1]
[0]
Table 131. 0x3D0: VCO_CAL_CFG
Bit
[7:4]
[3:0]
Table 132. 0x3D2: OSC_CONFIG
Bit
[7:6]
[5:3]
[2:0]
Table 133. 0x3DA: VCO_BAND_READBACK
Bit
[7:0]
Table 134. 0x3DB: VCO_AMPL_READBACK
Bit
[7:0]
Table 135. 0x3F8: ANALOG_TEST_BUS
Bit
[7:0]
Table 136. 0x3F9: RSSI_TSTMUX_SEL
Bit
[7]
[6:2]
[1:0]
Name
VCO_BAND_OVRW_VAL
Name
VCO_AMPL_OVRW_VAL
Name
Reserved
VCO_Q_AMP_REF
VCO_AMPL_OVRW_EN
VCO_BAND_OVRW_EN
Name
Reserved
VCO_CAL_CFG
Name
Reserved
XOSC_CAP_DAC
Reserved
Name
VCO_BAND_READBACK
Name
VCO_AMPL_READBACK
Name
ANALOG_TEST_BUS
Name
Reserved
Reserved
RSSI_TSTMUX_SEL
R/W
R/W
R/W
R/W
R/W
R
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
Reset
0
Reset
0
Reset
0
Reset
0
0
0
Rev. 0 | Page 96 of 100
Reset
0
Reset
0
Reset
0
0
0
0
Reset
0
1
26 MHz crystal oscillator (XOSC26N) tuning capacitor control word
Description
Write 0
Write 0
Description
Readback of the VCO bias current DAC after calibration
Description
Readback of the VCO bias current DAC after calibration
Description
To enable analog RSSI on ATB3, set ANALOG_TEST_BUS = 0x64 in
conjunction with setting RSSI_TSTMUX_SEL = 0x3.
Description
To enable analog RSSI on ATB3, set RSSI_TSTMUX_SEL = 0x3 in conjunction
with setting ANALOG_TEST_BUS = 0x64.
Description
Overwrite value for the VCO frequency band; active when
VCO_BAND_OVRW_EN = 1.
Description
Overwrite value for the VCO bias current DAC; active when
VCO_AMPL_OVRW_EN= 1.
Description
Reserved.
VCO amplitude level control reference DAC during Q phase
1: enable VCO bias current DAC overwrite
0: disable VCO bias current DAC overwrite
1: enable VCO frequency band overwrite
0: disable VCO frequency band overwrite
Description
Reserved.
VCO calibration state machine configuration. Set VCO_CAL_CFG =
0xF to bypass VCO calibration on the PHY_TX and PHY_RX
transitions. Set VCO_CAL_CFG = 0x1 to enable the VCO
calibrations on the transitions.