wm8350 Wolfson Microelectronics plc, wm8350 Datasheet - Page 199

• Manufacturer Part Number: wm8350
• Description: Wolfson Audioplus? Stereo Codec With Power Management
• Manufacturer: Wolfson Microelectronics plc

Production Data
23 WATCHDOG TIMER
w
The WM8350 includes a watchdog timer designed to detect a possible software fault condition where
the host processor has locked up. The watchdog timer checks for any write operation to the
watchdog control register R4 (04h) or receipt of a heartbeat signal from the host processor on GPIO9
(see Section 20). If neither event occurs within a programmable time, this is interpreted as a fault in
the host processor. The watchdog timer then raises an interrupt and/or generates a system reset; the
desired response to a watchdog timeout is set using the WDOG_MODE register field.
If GPIO9 is configured as HEARTBEAT input (GP9_FN = 0001, GP9_DIR = 1), then the Watchdog
Timer can only be reset by a rising logic level applied to the GPIO9 pin.
If GPIO9 is not configured as HEARTBEAT input, then the Watchdog Timer can only be reset by a
write operation to the watchdog control register R4 (04h).If a System reset is triggered by the
watchdog timeout, the WM8350 asserts the /RST pin and the /RST and /MEMRST (GPIO) reset
signals, resets the internal control registers and then initiates a start-up sequence.
The watchdog timer can be halted for debug purposes using the WDOG_DEBUG bit. The watchdog
can be disabled in Hibernate mode using the WDOG_HIB_MODE bit. The watchdog timer duration is
set using WDOG_TO, as described in Table 138.
The Watchdog timeout interrupt event is indicated by the SYS_WDOG_TO_EINT register field. This
is one of the second-level interrupts which triggers a first-level System Interrupt, SYS_INT (see
Section 24). This can be masked by setting the mask bit as described in Table 139.
R3 (03h)
System
control 1
R4 (04h)
System
control 2
R5 (05h)
System
Hibernate
Note: WDOG_HIB_MODE can be accessed through R4 or through R5. Reading from or writing to
either register location has the same effect.
Table 138 Controlling the Watchdog Timer
ADDRESS
BIT
5:4
2:0
7
7
7
WDOG_DEBU
G
WDOG_HIB_M
ODE
WDOG_MODE
[2:0]
WDOG_TO
[2:0]
WDOG_HIB_M
ODE
LABEL
DEFAULT
Dependan
CONFIG
settings
t on
101
0
0
0
Halts watchdog timer for system debugging
0 = normal operation
1 = WDOG halt
Watchdog behaviour in HIBERNATE state
0 = WDOG disabled in Hibernate
1 = WDOG controlled by WDOG_MODE in
Hibernate
Watchdog mode
00 = Disabled
01 = SYS_WDOG_TO interrupt on time-out
10 = WKUP_WDOG_RST interrupt and
11 = SYS_WDOG_TO interrupt on first time-
Protected by security key.
Watchdog timeout (seconds)
The timer is reset to this value when a
HEARTBEAT signal edge is detected or the
host writes to the watchdog control register.
000 = 0.125s
… (time doubles with each step)
101 = 4s
11x = Reserved
Protected by security key.
Watchdog behaviour in HIBERNATE state
0 = WDOG disabled in Hibernate
1 = WDOG controlled by WDOG_MODE in
Hibernate
System reset on time-out
out, WKUP_WDOG_RST interrupt and
System reset on second time-out.
DESCRIPTION
PD, June 2009, Rev 4.1
WM8350
199