71m6545h-igtr/f Maxim Integrated Products, Inc., 71m6545h-igtr/f Datasheet - Page 22

• Manufacturer Part Number: 71m6545h-igtr/f
• Description: Metrology Processors
• Manufacturer: Maxim Integrated Products, Inc.

Data Sheet 71M6545/H
communication with the 71M6545/H, supplying current samples and auxiliary information such as sensor
temperature via a serial data stream.
Up to three 71M6xx3 Isolated Sensors can be supported by the 71M6545/H. When a remote sensor
interface is enabled, the two analog current inputs become re-configured and a digital remote sensor
interface. For example, when control bit RMT2_E = 1, the IADC2-IADC3 analog pins are re-configured as
the digital interface pins to the remote sensor.
Each 71M6xx3 Isolated Sensor consists of the following building blocks:
•
•
•
•
•
•
During an ordinary multiplexer cycle, the 71M6545/H internally determines which other channels are
enabled with MUX_DIV[3:0] (I/O RAM 0x2100[7:4]). At the same time, it decimates the modulator output
from the 71M6xx3 Isolated Sensors. Each result is written to CE RAM during one of its CE access time
slots.
2.2.8.2 Communication between 71M6545/H and 71M6xx3 Isolated Sensor
The ADC of the 71M6xx3 derives its timing from the power pulses generated by the 71M6545/H and as a
result, operates its ADC slaved to the frequency of the power pulses. The generation of power pulses, as
well as the communication protocol between the 71M6545/H and 71M6xx3 Isolated Sensor, is automatic and
transparent to the user. Details are not covered in this data sheet.
2.2.8.3 Control of the 71M6xx3 Isolated Sensor
The 71M6545/H can read or write certain types of information from each 71M6xx3 remote sensor.
The data to be read is selected by a combination of the RCMD[4:0] and TMUXRn[2:0]. To perform a read
transaction from one of the 71M6xx3 devices, the MPU first writes the TMUXRn[2:0] field (where n = 2, 4, 6,
located at I/O RAM 0x270A[2:0], 0x270A[6:4] and 0x2709[2:0], respectively). Next, the MPU writes
RCMD[4:0] (SFR 0xFC[4:0]) with the desired command and phase selection. When the RCMD[4:2] bits
have cleared to zero, the transaction has been completed and the requested data is available in
RMT_RD[15:0] (I/O RAM 0x2602[7:0] is the MSB and 0x2603[7:0] is the LSB). The read parity error bit,
PERR_RD (SFR 0xFC[6]) is also updated during the transaction. If the MPU writes to RCMD[4:0] before a
previously initiated read transaction is completed, the command is ignored. Therefore, the MPU must wait
for RCMD[4:2]=0 before proceeding to issue the next remote sensor read command.
The RCMD[4:0] field is divided into two sub-fields, COMMAND=RCMD[4:2] and PHASE=RCMD[1:0], as
shown in
22
Power supply that derives power from pulses received from the 71M6545/H
Bi-directional digital communications interface
Shunt signal pre-amplifier
22-bit 2nd Order Sigma-Delta ADC Converter with precision bandgap reference (chopping amplifier)
Temperature sensor (for digitally compensating VREF)
Fuse system containing part-specific information
Table
Notes:
4.
000
001
010
011
100
101
110
111
1. Only two codes of RCMD[4:2] (SFR 0xFC[4:2]) are relevant for normal
Command
RCMD[4:2]
operation. These are RCMD[4:2] = 001 and 010. Codes 000 and 101
Command 1
Command 2
© 2008–2011 TERIDIAN Semiconductor Corporation
Reserved
Reserved
Reserved
Reserved
Invalid
Invalid
Table 4. RCMD[4:0] Bits
00
01
10
11
Phase Selector
RCMD[1:0]
IADC
IADC
IADC
Invalid
2
4
6
-IADC3
-IADC5
-IADC7
Associated TMUXRn
Control Field
TMUXR
TMUXR
TMUXR
---
2
4
6
[2:0]
[2:0]
[2:0]
PDS_6545_009
v1.0